167421
3
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
3
8 622 403 273
Safety precautions
Instructions for installation and connection
Fit a fuse in the amplifier power line no more than 30 cm from the vehi-
cle battery, in order to protect the battery in the event of a short-circuit
between it and the power amplifier. The amplifiers own fuse protects
the amplifier itself, but not the car battery. Disconnect the negative
terminal of the battery before carrying out installation and connec-
tion work.
Observe the vehicle manufacturer’s safety instructions (regarding air-
bags, alarm systems, trip computers, vehicle immobilisers).
The final stage must be installed professionally for reasons of safety.
The mounting surface must be suitable for the screws provided, and
must provide firm support.
When drilling holes, take care to avoid damage to vehicle components
(battery, cables, fuse boxes).
Fit the amplifier in a suitable location, e.g. beneath the seats or in the
trunk (Fig. 1). The mounting location must also be dry, and provide suf-
ficient ventilation for cooling of the amplifier. Use cable grommets when
passing cables through holes with sharp edges. Use loudspeakers with
an impedance of 2 to 4 (see table or installation drawing). Observe
the max. power handling specifications (music output). Do not connect
the loudspeakers to ground; only use the terminals provided. The cross-
section of the positive and negative cable must be at least 6 mm
2
.
GTA 480 amplifier
The amplifier is suitable for connection to car radios with Cinch connec-
tor. Use the Blaupunkt ISO Cinch adapter to connect the amplifier
to car radios with ISO connector. (7 607 893 093/ 7 607 855 094)
Applications and loudspeaker connection
Quadro-Mode Max Power 4 x 80 Watt / 4 Fig.3
Stereo-Mode Max Power 2 x 220 Watt / 4 Fig.6
Quadro-Mode RMS Power 4 x 40 Watt /4 Fig.3
Stereo-Mode RMS Power 2 x 110 Watt /4 Fig.6
Frequency response 10 Hz - 26.000 Hz
Signal-to-noise ratio > 80 dB
Stability 2
Inputsensitivity 0,3 - 8 V
Low-pass filter 40 - 160 Hz
High-Pass filter 40 - 600 Hz
Dimensions
D x W x H (mm) 290 x 57 x 243
Positive/negative connection
We recommend a cable cross-section of not less than 6 mm
2
. Run a
standard commercial positive cable to the battery and connect to the
fuse holder. Use cable grommets when passing cables through holes
with sharp edges. Bolt a standard commercial negative cable to a ground
point free of induced noise (car body bolt, body panel) - not to the neg-
ative battery pole. Clean the contact surface of the ground point down
to bare metal and coat with antiseize graphite petroleum.
Integral fuses
The integral fuses within the amplifier protect the final stage and the
entire electrical system in the event of a fault. Never bridge fuses or
replace fuses with a higher current rating.
Example connections
Power supply connection ............................................................ Fig. 2
Connection of car radio with cinch output ................................... Fig. 3
Loudspeaker connections ........................................................ Fig. 3-6
+12V
Connect remote amplifier connection to switchable
+12 V power source.
This enables the amplifier to be switched on and off with the radio’s On/
Off switch.
Level control
The Level control enables the input sensitivity of the final stage to be
matched to the output voltage of your car radio preamp output.
The range of adjustment extends from 0.3 V to 8 V.
Adjust the input sensitivity in accordance with the manufacturer’s spec-
ifications when connecting the amplifier to other radios.
Important: Turning the Level control clockwise increases the input sen-
sitivity of the amplifier, and thereby also the volume. The Level control is
however not a volume control; an increase in volume is not achieved in
the maximum position, even if this subjectively appears to be the case.
The system merely increases the volume more quickly when the vol-
ume is turned up on the radio.
Loudspeaker connections
(If the amplifier is to be connected in a bridged mode, proceed with the
section “Bridged loudspeaker connections”.)
As with any audio component, connection of the amplifier and speakers
with the correct polarity is essential for good bass reproduction. Ensure
therefore when connecting that the positive (+) amplifier terminal is con-
nected to the positive (+) loudspeaker terminal. The same applies to the
negative (-) terminals. The left-hand amplifier channel must also be con-
nected to the left-hand loudspeaker and the right-hand amplifier chan-
nel to the right-hand loudspeaker.
Bridged loudspeaker connections
The GTA can also be bridged in a mono configuration. This enables you
to use the amplifier for one or more subwoofer(s) or a mid-range speak-
er. In this configuration the amplifier sums the right-hand and left-hand
channels, delivering a single channel (mono) output.
Note: The amplifier can sum the right- and left-hand signal information
only if both the right- and left-hand RCA connections have been made.
CAUTION: The amplifier must be presented with a load of 4 Ohms
or higher in bridged mode. A lower load will cause the amplifier to
overheat or switch off. This can lead to permanent damage of the
unit.
GTA 480
The type of crossover (i.e. “low-pass” or “hi-pass”) and the desired cros-
sover frequency can be selected on the GTA 480. If, for example, you
wish to drive a pair of subwoofers, connect in accordance with the low-
pass diagram (fig. 2a).The crossover frequency is dependent upon the
loudspeaker frequency range (consult the loudspeaker manufacturer’s
data for the recommended frequency range).
“High- Pass” frequency control
This control is active when the switch is in the “Hi-pass” position, and
permits selection of the desired crossover frequency. Example: at a of
40 Hz, the loudspeaker has a frequency range of 40 Hz to
26.000 Hz.
“Low-pass” frequency control
This control is active when the switch is set to “Low-pass” and permits
selection of the desired crossover frequency. Example: at a setting of
40 Hz, the loudspeaker has a frequency range of 10 Hz to 40 Hz.
Operating indicator (POWER / PROTECTION)
Green lamp: Power amp on, regular operating condition
Red lamp: Power amp has been switched off electronically, due to a fault
or failure.
This information is subject to change without notice!
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt gta 480 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt gta 480 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info