165634
2
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
GB
Amplifier type
4/3/2-channel switching amplifier with integrated sub-bass crossover.
Installation
The amplifier BQX 320 can be connected to car radios equipped with a
PREAMP OUTPUT (DIN 45 326) or Cinch socket.
Use the adapter cable 7 607 873 000 (speaker plug DIN socket) to
connect the amplifier to a car radio with loudspeaker outputs. Several
amplifiers can be bridged via the 8-pin AUX OUT socket.
Safety Notes
Installation and connecting instructions
Disconnect the negative terminal of the battery during installation.
Select a suitable mounting place in the car for the BQX 320, e.g. at the
splashboard, below the dashboard, below the seats or in the boot. Make
sure the selected mounting place provides sufficient heat dissipation.
Prior to drilling the mounting holes, make sure that no cables and parts
of the vehicle will be damaged, fig. 1.
Leave ample clearance between the cables and other harnesses.
Use only loudspeakers having an impedance of 4 . Observe the rated
maximum capacity (music power) of the selected loudspeakers.
Use speaker cables with a cross section between of up 16 mm
2
. Do not
connect the loudspeakers to ground, use only the marked terminals.
Possible applications
Function select switch
1 Full-range 4 x 80 W or 2 x 160 W
2 High-pass 4 x 80 W
3 High-pass 2 x 80 W
+
Low-pass 2 x 80 W or 1 x 160 W
4 Full-range 2 x 80 W
+
Low-pass 2 x 80 W or 1 x 160 W
5 Low-pass 2 x 160 W
Switch settings
Bass boost setting ON 10 dB bass boost at 45 Hz
80 Hz / 120 Hz Subwoofer crossover frequency
Plus/minus connection
Route the enclosed positive cable to the battery and connect it via the
fuse contact. Use the enclosed cable ducts at sharp-edged holes.
Screw the enclosed negative cable to an interference-free ground spot
(chassis screw or plate). Do not connect it to the negative terminal of the
battery. The contact area of the ground source must be blank and
lubricated with graphite grease.
Examples
Connection to car radios with DIN output Fig. 2
Connection to car radios with Cinch output Fig. 3
The settings of the crossover switch “80 Hz - 120 Hz” and “Bass Boost”
depends on the type of loudspeaker used, the accoustic properties of the
car interior and on personal preferences.
For frequencies, see product manual and specification.
When connecting the amplifier via Cinch or loudspeaker sockets, the
switching line must be connected.
Loudspeaker connection Fig, 4, 5, 6, 7
Function select 1 4 x 80 W or 2 x 160 W
Function select 2 4 x 80 W with subwoofing
Function select 3 2 x 80 W and 2 x 80 W
or 1 x 160 W with subwoofing
Function select 4 2 x 80 W and 2 x 80 W
or 1 x 160 W with subwoofing
Function select 5 2 x 160 W with subwoofing
GAIN ADJ
The Gain Adjust control button can be adjusted between 0.3 and 2 V.
When connecting a Blaupunkt car radio, adjust the control button to 2 V.
If a car radio of another brand shall be connected, adjust the input
sensitivity as detailed in the car radio specification.
Bass Level Adj
Use the bass level adjust control to set the subwoofer volume ± 10 dB.
Specification
Max. power: 2 x 80 W or 1 x 160 W into 4
RMS power: 2 x 40 W or 2 x 80 W with 1 % THD
(DIN 45500)
Distortion factor: < 0,01 % at 10 W, 1 kHz, 4
Frequency response: 10 Hz - 90 kHz (-3 dB)
Signal-to-noise ratio: >100 dB(A)
Channel separation: >60 dB / 1 kHz
Protected against short-circuit and overtemperature.
Inputs: 8-pin DIN, 4 x Cinch (RCA) gold-plated
Outputs: AUX OUT (8-pin DIN), 4 speaker outputs, 4 gold-plated
Dimensions ( W x H x D): 350 x 45 x 270 mm
Changes reserved
F
Description du produit
Amplificateur 4/3/2 canaux avec bloc de commutation et diviseur de
fréquence subwoofer intégré.
Notice de montage
L’amplificateur BQX 320 est conçu pour le branchement sur les autoradios
munis d’un “PREAMP OUTPUT” conformément à la norme DIN 45 326
ou d’une prise Cinch.
Pour brancher l’appareil sur les autoradios équipés de sorties haut-
parleurs, utiliser le câble adaptateur 7 607 873 000 (prise mâle du haut-
parleur prise femelle DIN). La prise 8 pôles AUX OUT permet de
connecter plusieurs amplificateurs en même temps.
Recommandations de
sécurité
Consignes de montage et de branchement
Débrancher le pôle négatif de la batterie pendant toute la durée des
travaux de branchement et de montage de l’appareil.
Le BQX 320 doit être monté à un emplacement spécialement prévu p. ex.
sur le tablier d’auvent, sous le tableau de bord, sous les sièges ou dans
le coffre à bagages. L’emplacement de montage choisi devra permettre
une évacuation suffisante de la chaleur. Avant de percer les trous de
fixation, veiller à n’endommager ni câbles ni pièces déjà présents dans
le véhicule, fig. 1.
Poser tous les câbles à bonne distance des harnais de câbles afin
d’éviter tout parasitage.
Utiliser exclusivement des haut-parleurs d’impédance 4 . Respecter
l’intensité maximum (puissance musicale efficace).
Pour le raccordement des haut-parleurs, utiliser des câbles pouvant aller
jusqu’ à 16 mm
2
. Ne pas mettre les haut-parleurs à la masse, n’utiliser
que les bornes indiquées.
Mise en service et sélections réalisables:
Sélecteur de fonction (Function Select)
1 Full Range 4 x 80 W ou 2 x 160 W
2 High Pass 4 x 80 W
3 High Pass 2 x 80 W
+
Low Pass 2 x 80 W ou 1 x 160 W
4 Full Range 2 x 80 W
+
Low Pass 2 x 80 W ou 1 x 160 W
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt bqx 320 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt bqx 320 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds als bijlage per email.

De handleiding is 0,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info