614226
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Wireless PIR Motion Sensor (IR-S1)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Learn/Test Button & LED indicator
Press the button to transmit a learn/test code and enter Test
mode for 3 minutes. The LED will light up whenever a movement
is detected under Test mode.
2. Battery Insulator
3. Supervision Enable/Disable Jumper Switch
(JP2)
4
. High/Low Sensitivity Jumper Switch (JP3)
5. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening.
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x PIR Sensor
4 x wall plugs and screws
2 x 1.5V alkaline batteries (pre-installed)
Supervision Enable/Disable Jumper Switch (JP2)
If enabled, the PIR sensor will transmit supervision signal to
Control Panel periodically for the sensor to monitor PIR sensor
condition.
Jumper set to ON = supervision function is Disabled (Default)
Jumper set to OFF = supervision function is Enabled
High/Low Sensitivity Jumper Switch (JP3)
Jumper set to ON = PIR sensitivity is set to High
Jumper set to OFF= PIR sensitivity is set to Low (Default)
Put the Control Panel into learning mode, then press the learn
button to transmit learn code. Please refer to Control Panel
manual for to complete the learning process.
The PIR Sensor has knockouts on the back where plastic is
thinner. The 2 center knockouts are for flat wall mounting, and the
4 side knockouts are for corner mounting.
1. Break through the knockouts; use the knockouts to mark
position on the wall or corner.
2. Drill holes into the wall or corner using the knockouts as
template.
3. Fix the PIR Sensor base onto the wall with the screws and
plugs provided.
4. Replace the PIR Sensor cover onto the base.
S
S
l
l
e
e
e
e
p
p
T
T
i
i
m
m
e
e
r
r
The PIR features a “sleep time” of approximately 1 minute for
power conservation. After transmitting a detected movement, the
PIR will not retransmit for 1 minute. Any further movement
detected during this sleep period will extend the sleep time by
another minute. In this way continuous movement in front of a
PIR will not unduly exhaust the battery.
T
T
e
e
s
s
t
t
M
M
o
o
d
d
e
e
Press the Test Button to enter Test mode for 3 minutes. Sleep
timer will be disabled under Test mode, and the LED indicator will
flash every time a movement is detected. Use the Test mode to
determine PIR detection coverage and plan the installation
location accordingly.
L
L
E
E
D
D
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
Off Normal Operation
On (2 seconds) - When Tamper Switch is triggered
- Movement detection under low battery,
tamper triggered, or Test mode.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Surface Fixing
Knockouts x 2
(Inside)
Corner Fixing
Knockouts x 4
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt IR-S1L bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt IR-S1L in de taal/talen: Engels als bijlage per email.

De handleiding is 0,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Blaupunkt IR-S1L

Blaupunkt IR-S1L Gebruiksaanwijzing - Nederlands - 2 pagina's

Blaupunkt IR-S1L Gebruiksaanwijzing - Deutsch - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info