686548
22
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
en Trouble shooting
22
3Trouble shooting
Tr oubl e s hoot i ng
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Notes
If appears on the display, press and hold the
button for the relevant cooking zone in order to read
the fault code.
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
Cleaning
How do I clean the hob?
Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dish-
water detergent (concentrated) or scouring pads.
You can find more information on cleaning and caring for your hob in the section on ~ "Cleaning"
Display Possible cause Solution
None The power supply has been disconnected. Use other electrical devices to check whether a short-circuit has
occurred in the power supply.
The device has not been connected in accord-
ance with the circuit diagram.
Ensure that the device has been connected in accordance with
the circuit diagram.
Electronics fault. If the fault cannot be eliminated, inform the technical after-sales
service.
The displays flash The control panel is damp or an object is cover-
ing it.
Dry the control panel or remove the object.
The Ù indicator flashes in the
hotplate displays
A fault has occurred in the electronics. To acknowledge the fault, cover the control panel with your hand.
”ƒ
The electronics have overheated and have
switched off the corresponding hotplate.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the hob.
”…
The electronics have overheated and have
switched off all hotplates.
Ӡ + heat setting and acous-
tic signal
There is a hot pan in the area of the control
panel. There is a risk that the electronics will
overheat.
Remove the pan. The fault display goes out shortly afterwards.
You can continue to cook.
Ӡ and acoustic signal
There is a hot pan in the area of the control
panel. To protect the electronics, the hotplate
has been switched off.
Remove the pan. Wait for a few seconds. Touch any control. If the
fault display goes out, you can continue to cook.
”‚/”‡
The hotplate has overheated and switched itself
off to protect the work surface.
Wait until the electronics have cooled down sufficiently and
switch the hotplate on again.
”‰
The hotplate was operating for an extended
period without interruption.
The automatic safety switch-off function has been activated. See
section
“Š‹‹‹
“Š‹‚‹
The supply voltage is faulty; outside of the nor-
mal operating range.
Contact your electricity provider.
—…‹‹
The hob is not connected properly Disconnect the hob from the power supply. Ensure that it has
been connected in accordance with the circuit diagram.
Do not place hot pans on the control panel.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt 5II84352 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt 5II84352 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Blaupunkt 5II84352

Blaupunkt 5II84352 Gebruiksaanwijzing - Nederlands - 48 pagina's

Blaupunkt 5II84352 Gebruiksaanwijzing - Deutsch - 24 pagina's

Blaupunkt 5II84352 Gebruiksaanwijzing - Français - 28 pagina's

Blaupunkt 5II84352 Installatiehandleiding - Svenska, Alle talen - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info