388538
4
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
4
ENGLISH
Features
This tool includes some or all of the following features (fig. A)
1. Variable speed switch
2. Lock-on button
3. Bit holder
4. Locking ring
5. Forward/reverse switch
6. Direction of rotation indicator
7. Torque adjustment collar
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Fitting and removing a drill bit or screwdriver bit (fig. B)
Fitting
This tool uses screwdriver bits and drill bits with a 1/4" (6.35 mm)
hexagonal shank.
Insert the bit shaft into the bit holder (3) and press it
down until it clicks in place.
Removing
Warning! The drill bit may be hot just after drilling.
Pull the locking ring (4) backwards and take the bit out of
the bit holder.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, move the forward/
reverse switch (5) to the right. The direction indicator (6)
shows a forward pointed arrow.
For loosening screws or removing a jammed bit, move the
forward/reverse switch to the left. The direction indicator
shows a backward pointed arrow.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the torque or drill position (fig. D)
This tool is fitted with a collar to set the torque for tightening
screws.
For drilling, turn the collar (7) to the left until the symbol
aligns with the marking (8).
For screwdriving, set the collar to the desired setting. If you
do not yet know the desired setting, proceed as follows:
Turn the collar (7) completely to the right (lowest torque).
Tighten the first screw.
If the clutch ratchets before the desired result is
achieved, increase the torque by turning the collar to
the left. Continue tightening the screw. Repeat until
you reach the correct setting. Use this setting for the
remaining screws.
Switching on and off (fig. A)
To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed.
To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Hints for optimum use
Drilling
Always apply a light pressure in a straight line with the
drill bit.
Just before the drill tip breaks through the other side of
the workpiece, decrease pressure on the tool.
Use a block of wood to back up workpieces that may splinter.
Use spade bits when drilling large diameter holes in wood.
Use masonry drill bits when drilling into light masonry.
Use HSS drill bits when drilling in metal.
Use a lubricant when drilling metals other than cast iron
and brass.
Make an indentation with a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
Always use the correct type and size of screwdriver bit.
If screws are difficult to tighten, try applying a small amount
of washing liquid or soap to the thread as a lubricant.
Always hold the tool and screwdriver bit in a straight line
with the screw.
When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw.
A pilot hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a clearance hole with
a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table below.
Screw size Pilot hole ø (softwood)
No. 6 (3.5 mm) 2 mm
No. 8 (4 mm) 3.2 mm
No. 10 (5 mm) 3.5 mm
Screw size Pilot hole ø (hardwood)
No. 6 (3.5 mm) 2.5 mm
No. 8 (4 mm) 3.5 mm
No. 10 (5 mm) 4.0 mm
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker kr 2000 k bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker kr 2000 k in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info