382760
6
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
6
ENGLISH
Adjusting the saw blade support roller
(fi g. A & B)
Loosen the screw (9).
Push the shoe plate (4) forward until the saw
blade support roller (5) touches the back edge
of the saw blade (7).
Tighten the screw (9).
Fitting and removing the saw blade (fi g. C)
Before fi tting or removing the saw blade (7) the
saw blade support roller (5) must be adjusted
to the rear position so that it does not contact
the blade.
Loosen (do not remove) the two screws (6).
Hold the saw blade (7) with the teeth facing
forward.
Insert the shank of the saw blade (7) into the
blade holder (8) as far as it will go.
Slightly tighten the two screws (6) alternately
to position the blade, then fully tighten the two
screws (6).
Adjust the saw blade support roller (5) as
described above.
To remove the saw blade (7), turn both screws
(6) one turn counter-clockwise.
Saw blade storage (fi g. D)
Saw blades can be stored in the storage
compartment (3) at the rear of the tool.
Open the cover of the saw blade storage
compartment (3).
Remove or store saw blades (7) in the storage
compartment. (3).
Close the cover of the saw blade storage
compartment (3) and make sure that it is
latched closed.
Cut line blower (fi g. E)
To aid visibility when cutting, your jigsaw is
equipped with a cut line blower (10) which will
keep the work area clear of dust as you saw.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from
misuse, prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These include:
Injuries caused by touching any rotating/
moving parts.
Vibration
The declared vibration emission values stated in
the technical data and the declaration of conformity
have been measured in accordance with
a standard test method provided by EN 60745 and
may be used for comparing one tool with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used. The vibration level may increase
above the level stated.
When assessing vibration exposure to determine
safety measures required by 2002/44/EC to
protect persons regularly using power tools in
employment, an estimation of vibration exposure
should consider, the actual conditions of use and
the way the tool is used, including taking account
of all parts of the operating cycle such as the times
when the tool is switched off and when it is running
idle in addition to the trigger time.
Labels on tools
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Electrical safety
This tool is double insulated; therefore
no earth wire is required. Always check
that the power supply corresponds to the
voltage on the rating plate.
If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to
avoid a hazard.
Features
1. On/off switch
2. Lock-on button
3. Saw blade storage compartment
4. Shoe plate
5. Saw blade support roller
Assembly
Warning! Before attempting any of the following
operations, make sure that the tool is switched
off and unplugged and that the saw blade has
stopped. Used saw blades may be hot.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker ast 7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker ast 7 in de taal/talen: Duits, Engels, Frans, Pools, Turks als bijlage per email.

De handleiding is 1,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info