578039
5
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
5
ENGLISH
Features
1. Cutting head
2. Lock switch
3. On/off trigger switch
4. Charging socket
5. Charger plug
6. Charger
Warning! Before cleaning, adjustment or replacing the cutting
head. Set the lock switch to OFF (0).
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. B)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that
were easily done before. When charging the battery for the
first time, or after prolonged storage, it will only accept an
80% charge. After several charge and discharge cycles, the
battery will attain full capacity. The battery may become
warm while charging; this is normal and does not indicate a
problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
X To charge the battery, insert the charger plug (5) into the
charging socket (4).
X Plug in the charger (6). Switch on at the mains.
X Leave the tool connected to the charger for 12 hours.
The charger may hum and become warm while charging; this
is normal and does not indicate a problem.
Generally, a charging time of 8 hours will enable the tool to
operate at an effective power level for most tasks. However,
further charging for up to 12 hours could significantly
increase the run time, depending on the battery and charging
conditions.
X Before using the tool, unplug the charger and disconnect
the tool from the charger.
Warning! The tool will not operate while it is connected to the
charger.
Switching on and off (fig. C)
X To switch the tool on, push the lock switch (2) into the ON
position (I) and squeeze the trigger switch (3).
X To switch the tool off, release the trigger switch and slide
the lock switch to the OFF position (0).
Cutting
Hold the tool firmly while cutting.
X Switch the tool on and let the blade run freely for a few
seconds before starting the cut.
X Apply only a gentle pressure to the tool while performing
the cut.
Keep hands away from the cutting area and be aware of
materials and surfaces under the cutting area that the blade
may contact.
Do not force the tool. If the tool will not cut, consider the
thickness or hardness of the material, does the tool require
charging, does the cutting head require replacement?
Do not attempt to cut metal or materials that may damage
the cutting head.
Warning! Before cleaning, adjustment or replacing the cutting
head. Set the lock switch to OFF (0).
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
unplug the charger before cleaning it.
X Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
X Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner. Never let
any liquid get inside the tool and never immerse any part of
the tool into liquid.
Replacing the cutting head.
The cutting head contains no serviceable parts and should be
replaced whenever worn or damaged. Do not attempt to
sharpen the cutting surfaces. Replacement cutting heads are
available from your Black & Decker repair agent.
Fitting and removing the cutting head (fig. A)
To remove the cutting head (1) for cleaning or replacement.
X Separate the scissor blades and set the lock switch to the
OFF (0) position.
X To exchange cutting heads, grasp the scissors as shown in
figure A with fingers at the side of the cutting head and the
hand away from the blades.
X Press in on the sides of the cutting head and pull
straight out.
To attach a cutting head, line it up with the body of the scissors
and push it on until it snaps into place. If the cutting head does
not line up easily, carefully separate the blades from each other
first then re-attach.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker SZ360 T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker SZ360 T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker SZ360 T1

Black Decker SZ360 T1 Snelstart handleiding - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info