25090
5
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
5
ENGLISH
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing accessories (fig. A)
Make sure that the tool is switched off and unplugged.
Activate the spindle lock (2) by setting it to position B as
shown.
Slacken the collet nut (5) by turning counterclockwise.
Insert the shaft of the accessory into the collet as far as it
will go.
Securely tighten the collet nut.
Release the spindle lock (2) by setting it to position A as
shown.
Warning!
Make sure that the collet size matches the shaft diameter.
Never tighten the collet nut without an accessory in the
collet.
Tighten and loosen the collet by hand if possible.
If necessary, use the supplied wrench to loosen the collet.
Do not use any tools that could mark the finish or break
the collet.
Replacing collets (fig. B)
This tool is supplied with a 3.2 mm collet. Different sizes are
available as an accessory to accomodate a wide range of
accessories. To fit the correct collet for the accessory to be
used:
Make sure that the tool is switched off and unplugged.
Activate the spindle lock (2) by setting it to position B as
shown.
Remove the collet nut (5) by turning counterclockwise.
Pull the collet off the spindle (6).
Place the new collet into the spindle.
Loosely screw the collet nut onto the spindle.
Release the spindle lock (2) by setting it to position A as
shown.
Use
Warning!
Let the tool work at its own pace. Do not overload.
If you are not sure about the correct speed setting, start
with a low speed setting and gradually increase it until you
find the optimum setting.
Where indicated, never exceed the speed rating of an
accessory. The wire brush accessory must not be used
above speed setting 3 (15,000 min
-1
).
Variable speed control (fig. C)
The variable speed control allows you to adapt the speed of
the tool to the application.
Set the control knob (3) to the desired setting. At setting 1
the tool will operate at low speed, 8,000 min
-1
. At setting 6
the tool will operate at the maximum speed, 27,000 min
-1
.
The table below suggests settings for different applications.
Application Setting
Drilling holes 4-5
Cutting metal 5-6
Engraving metal 4-5
Removing rust 1-2
Sharpening 3-5
Polishing 1-2
Sanding wood 5-6
Removing paint 3-5
Switching on and off (fig. D)
To switch the tool on, slide the on/off switch (1) forward
(position I).
To switch the tool off, slide the on/off switch to the rear
(position O).
Hints for optimum use (fig. E)
Always hold the tool securely. For precision work, hold the
tool near the front.
Do not exert too much pressure on the tool.
Consult your retailer for more information on available
accessories.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker RT650 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker RT650 in de taal/talen: Nederlands als bijlage per email.

De handleiding is 1,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker RT650

Black Decker RT650 Gebruiksaanwijzing - English - 16 pagina's

Black Decker RT650 Gebruiksaanwijzing - Français, Italiano, Português, Espanôl, Norsk - 84 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info