577932
5
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
5
ENGLISH
(Original instructions)
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Labels on tool
The following pictograms are shown on the tool:
;
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Extension cables
u A 2 or 3 core cable may be used as the appliance is
double insulated and of class II construction.
u Up to 30m (100 ft) can be used without loss of power.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Heat control knob
3. Nozzle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting an accessory
A selected range of accessories can be obtained from your
local retailer.
w Cone nozzle: Concentrates the air stream on a smaller
area.
w Fish tail: Spreads the air stream over a wider area
w Spoon reector: For soldering pipes.
w Glass protector: For the protection of glass during paint
stripping.
w Scraper: For the removal and stripping paint and
varnish.
u Fit the connecting piece of the accessory over the nozzle
(2).
Use
Setting the temperature (g. A)
u To increase the temperature setting, turn the heat control
knob (2) clockwise.
u To reduce the temperature setting, turn the heat control
knob anti-clockwise.
Switching on and off
u To switch the tool on at the low air speed, low heat, set the
on/off switch to position I.
u To switch the tool on at the high air speed, high heat, set
the on/off switch to position II.
u To switch the tool off, set the on/off switch to position O.
Using the tool
Your tool is tted with a thermostat for your safety. Using the
tool continuously for very long periods or other severe duty
cycles may cause the tool to overheat and stop working. It is
therefore recommended that you allow the tool to cool down at
regular intervals during use.
u Allow the tool to heat up for a few seconds before use.
u At rst use some smoke may emit from the nozzle. This is
normal and will soon decrease.
u Your tool is capable of many different heat settings using
a combination of the two settings on the trigger and the
variable heat control dial.
u Use a low temperature setting for drying paint and varnish,
removing stickers, shrinking insulation tubes, and thawing
frozen pipes.
u Use a medium temperature setting for welding plastics,
bending plastic pipes, and loosening tight nuts and
screws.
u Use a high temperature setting for removing paints and
lacquers, and soldering plumbing joints.
u If you are unsure about using this tool on a particular
material, start with a low temperature setting and perform
a test on scrap material.
Hands free use (g. B)
The tool has stand locations (4) to facilitate hands free use.
u Place the tool with the nozzle up on a surface where it
cannot be tipped over.
u Secure the cable to prevent pulling the tool over.
Warning! Always point the tool away from yourself or other
persons. Do not touch the nozzle. Take care that no material
drops into the nozzle.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KX2200 T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KX2200 T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info