577928
5
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
5
ENGLISH
Features
1. On/off switch
2. Heat control knob
3. Nozzle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting an accessory
A selected range of accessories can be obtained from your
local retailer.
- Cone nozzle Concentrates the air stream on a
smaller area
- Fish tail Spreads the air stream over a wider
area
- Spoon reflector For soldering pipes
- Glass protector For the protection of glass during
paint stripping
- Scraper For the removal of stripping paint and
varnish
Fit the connecting piece of the accessory over the nozzle (3).
Warning! Ensure the tool is switched off and cooled before
fitting any accessory.
Use
Warning! Let the tool work at its own pace. Do not overload.
Setting the temperature (fig. A)
To increase the temperature setting, turn the heat control
knob (2) clockwise.
To reduce the temperature setting, turn the heat control
knob anti-clockwise.
Switching on and off
To switch the tool on, set the on/off switch (1) to position I.
To switch the tool off, set the on/off switch to position O.
Using the tool
Allow the tool to heat up for a few seconds before use.
At first use some smoke may emit from the nozzle. This is
normal and will soon decrease.
Use a low temperature setting for drying paint and
varnish, removing stickers, shrinking insulation tubes, and
thawing frozen pipes.
Use a medium temperature setting for welding plastics,
bending plastic pipes, and loosening tight nuts and
screws.
Use a high temperature setting for removing paints and
lacquers, and soldering plumbing joints.
If you are unsure about using this tool on a particular
material, start with a low temperature setting and
perform a test on scrap material.
Handsfree use (fig. B)
The tool has stand locations (4) to facilitate handsfree use.
Place the tool with the nozzle up on a surface where it
cannot be tipped over.
Secure the cable to prevent pulling the tool out of the stand.
Warning! Always point the tool away from yourself or other
persons. Do not touch the nozzle. Take care that no material
drops into the nozzle.
Paint stripping
Direct the hot air at the working area to heat up the paint.
Do not burn the paint. Keep the nozzle at least 25 mm (1")
from the surface.
When the paint softens, remove the paint using a scraper.
Scrape the softened paint immediately or it will harden
again.
Scrape with the grain of the wood wherever possible.
Do not allow paint and debris collecting on the scraper.
When scraping from a vertical position, scrape
downwards to prevent the paint from falling back into the
nozzle.
When stripping paint from a surface next to glass, take
the necessary measures to protect the glass from the
heat.
Warning! Do not attempt to strip paint from metal
framed windows.
Dispose of all paint debris safely and ensure that the
work area is thoroughly cleaned after use.
Cooling down
During use, the nozzle of the tool becomes extremely hot.
After switching off, leave the tool to cool down for at least
30 minutes.
Place the tool with the nozzle up on a surface where it
cannot be tipped over.
To speed up the cooling time, run the tool on a low
minimum temperature setting for a few minutes before
switching off.
Maintenance
The tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactorily operation depends upon proper tool care and
regular cleaning.
Regularly clean the ventilation slots with a clean, dry
paint brush.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KX2000K T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KX2000K T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker KX2000K T1

Black Decker KX2000K T1 Gebruiksaanwijzing - Polski - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info