579751
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
8
7. Laser aperture
8. Shoe
9. Saw blade
10. Saw blade guard
11. Riving knife
12. Saw dust outlet
Assembly and adjustment
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and
that the saw blade has stopped.
Removing and fitting a saw blade (fig. A)
Removing
Keep the spindle lock button (5) depressed and rotate the
blade until the spindle lock engages.
Loosen and remove the blade retaining screw (13) by turning
it counterclockwise using the spanner (14) supplied.
Remove the outer washer (15).
Remove the saw blade (9).
Fitting
Place the saw blade onto the inner flange (16), making
sure that the arrow on the blade points in the same
direction as the arrow on the tool.
Fit the outer washer (15) on the spindle, with the raised
part pointing away from the saw blade.
Insert the blade retaining screw (13) into the hole.
Keep the spindle lock button (5) depressed.
Securely tighten the blade retaining screw by turning it
clockwise using the spanner (14) supplied.
Adjust the riving knife as described below.
Adjusting the riving knife (fig. B)
The riving knife prevents the saw blade from jamming during
rip sawing operations. The riving knife must be adjusted after
replacing the saw blade.
Loosen the screws (17), using the spanner (14), while holding
the riving knife in position.
Position the riving knife (11) as shown.
The distance between the toothed rim and the riving knife
should be 2 - 3 mm.
The height difference between the toothed rim and the
lower end of the riving knife should be 2 - 3 mm.
Tighten the screws.
Fitting and removing the parallel fence (fig. C)
The parallel fence is used to saw in a straight line parellel to
the edge of the workpiece.
Fitting
Loosen the locking knob (18).
Insert the parallel fence (19) through the openings (20).
Slide the parallel fence into the desired position.
Tighten the locking knob.
Removing
Loosen the locking knob.
Pull the parallel fence off the tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
This tool can be used in the right hand or the left hand.
Adjusting the sawing angle (fig. D)
The default angle between the saw blade and the shoe is 90°.
Use a square to check that the angle between the saw
blade and the shoe is 90°. If the angle does not measure
90° adjust as follows:
Loosen the locking knob (21) to unlock the saw shoe.
Loosen the locknut (22) on the adjusting screw (23).
Screw the adjusting screw in or out to achieve a 90° angle.
Retighten the locknut.
Tighten the locking knob to lock the saw shoe in place.
Adjusting the depth of cut (fig. E)
The depth of cut should be set according to the thickness of
the workpiece. It should exceed the thickness by approx. 2 mm.
Loosen the knob (24) to unlock the saw shoe.
Move the saw shoe (8) into the desired position. The
corresponding depth of cut can be read from the scale (25).
Tighten the knob to lock the saw shoe in place.
Adjusting the mitre angle (fig. F)
This tool can be set to mitre angles between 0° and 45°.
Loosen the locking knob (21) to unlock the saw shoe.
Move the saw shoe (8) into the desired position. The
corresponding mitre angle can be read from the scale (26).
Tighten the locking knob to lock the saw shoe in place.
Switching on and off
To switch the tool on, move the lock-off button (2) into the
unlock position and squeeze the on/off switch (1).
To switch the tool off, release the on/off switch.
Sawing
Always hold the tool with both hands.
Let the blade run freely for a few seconds before starting
the cut.
Apply only a gentle pressure to the tool while performing
the cut.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KS66L T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KS66L T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info