580888
7
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
7
ENGLISH
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features:
1. On/off switch
2. Lock-on button
3. Dust extraction outlet
4. Shoe plate
5. Saw blade support roller
Fig. E
6. Saw blade storage compartment (KS602E & KS603E)
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped. Used saw blades may be hot.
Adjustingthesawbladesupportroller(g.A&B)
u Loosen the two screws (8).
u Push the blade support roller (5) forward until it touches
the back edge of the saw blade (7).
u Tighten the two screws (8).
Fittingandremovingthesawblade(g.C)
u Before tting or removing the saw blade (7) the saw blade
support roller (5) must be adjusted to the rear position so
that it does not contact the blade.
u Loosen (do not remove) the two screws (10).
u Hold the saw blade (7) with the teeth facing forward.
u Insert the shank of the saw blade (7) into the blade holder
(9) as far as it will go.
u Slightly tighten the two screws (10) alternately to position
the blade, then fully tighten the two screws (10).
u Adjust the saw blade support roller (5) as described above.
u To remove the saw blade (7), turn both screws (10) one
turn counter-clockwise.
Connectingavacuumcleanertothetool(g.D)
An adaptor (11) is required to connect a vacuum cleaner or
dust extractor to the tool. The adaptor can be purchased from
your local Black & Decker retailer.
u Push the adaptor (11) into the dust extraction outlet (3).
u Connect the vacuum cleaner hose (12) to the adaptor (11).
Sawbladestorage(KS602E&KS603Eonly)(g.E)
Saw blades (7) can be stored in the storage compartment (6)
located on the side of the tool
u Open the cover of the saw blade storage compartment (6)
by holding the tab on the top of the door and pulling outwards.
u Remove or store saw blades (7) in the storage
compartment (6).
u Close the cover of the saw blade storage compartment (6)
and make sure that it is latched closed.
Cutlineblower(g.F)
u To aid visibility when cutting, your jigsaw is equipped with
a cut line blower (13) which will keep the work area clear
of dust as you saw.
Use
Adjustingtheshoeplateforbevelcuts(g.G)
The shoe plate can be set to make either a straight cut or a
left or right bevel cut at an angle of 45°.
u Loosen the screws (8).
u Pull the shoe plate (4) forward, rotate the shoe plate (4) to
the left or right and push it back into the 45° location.
u Push the blade support roller (5) forward until it touches
the saw blade (7).
u Tighten the screws (8).
To reset the shoe plate for straight cuts:
u Loosen the screws (8).
u Pull the shoe plate (4) forward, rotate to the centre and
push it back into the 0° location.
u Push the blade support roller (5) forward until it touches
the saw blade (7).
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KS603E T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KS603E T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker KS603E T1

Black Decker KS603E T1 Gebruiksaanwijzing - Polski, Türkiye - 76 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info