497050
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7
FITTING THE DRILL BIT (KEYED CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
Rotate the barrel
of the chuck until
the jaws are
sufficiently open.
Insert the drill bit
in the jaws of the
chuck. Insert the
chuck key with
the end of the chuck key in one of the three holes in the
body of the chuck and the head of the chuck key
engaged with the barrel of the chuck. Turn the chuck
key clockwise to tighten the jaws and securely grip the
drill bit. Remove the chuck key.
REMOVING THE CHUCK (KEYLESS CHUCKS)
Proceed as follows:
To remove the chuck,
open the jaws, hold
it firmly in one hand
and with a screwdriver
held in the other hand,
turn the set-screw in
the chuck clockwise
approximately one
turn, to loosen it.
Place an allen key in
the chuck and tighten the jaws. Give the allen key a
short powerful blow in an anti-clockwise direction with
a hammer to loosen the chuck on the spindle. Remove
the allen key. Use the screwdriver to turn the set-
screw clockwise until it totally disengages from the
spindle. Remove the chuck from the spindle by rotating
it anti-clockwise. To fasten the chuck, put it on the
thread and turn it clockwise until it stops. Put in the
screw and turn it anti-clockwise until absolutely firm.
REMOVING THE CHUCK (KEYED CHUCKS)
Proceed as follows:
To remove the chuck,
open the jaws of the
chuck with the chuck
key. Hold the chuck
firmly in one hand, and
with a screwdriver
turn the screw set in
the chuck clockwise
with the other hand
until it comes out.
Use only the correct chuck key. Place the chuck key
into the chuck, and hold the drill firmly in one hand with
the chuck pointing away from you. Rotate the chuck so
that the chuck key is just above the horizontal position
on the right hand side of the machine. Give the
crossbar end of the key a sharp downward blow with a
mallet or light hammer. The chuck should now be
sufficiently loose to be unscrewed by hand.
FITTING THE SIDE HANDLE
Proceed as follows:
Position the side
handle on the
body of your drill.
Rotate the handle
around the body
of your drill until it
is in the desired
position. Tighten the handle by turning clockwise.
SETTING THE ADJUSTABLE DEPTH STOP
Proceed as follows:
Fit the drill bit. Loosen the side handle.
Slide the depth stop
until the end of the
depth stop aligns
with the end of the
drill bit. Slide the
depth stop until the
distance between
the end of the depth
stop and the end of the drill bit is equal to the length of
the screw you will fit. Tighten the side handle.
PREPARING YOUR DRILL FOR OPERATION
Proceed as follows:
Fit the correct
accessory for the job.
Set the depth stop if
required. Set the
speed of your drill.
On two-speed drills,
set the two-speed switch to ‘1’ (low-speed) or ‘2’ (high-
speed), or set the variable speed control to the desired
speed. As a general rule, for large size drill bits use low
speeds and for smaller drill bits use high speeds.
Set the forward/
reverse switch to the
desired direction of
rotation. Never
change the setting of
the hammer switch,
ENGLISH
1
2
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker KD354 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker KD354 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker KD354

Black Decker KD354 Gebruiksaanwijzing - Nederlands - 64 pagina's

Black Decker KD354 Gebruiksaanwijzing - Deutsch - 44 pagina's

Black Decker KD354 Gebruiksaanwijzing - Français, Italiano, Português, Espanõl, Dansk, Svenska, Norsk, Suomi - 64 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info