474472
5
Verklein
Vergroot
Pagina terug
1/47
Pagina verder
5
Ensure that the electrical supply cable is
not twisted before you begin to assemble
the handle.
D
Locate the two pins on the switch box (13)
with the holes in the upper handle (12).
Fit the retaining plate (23) over the stem
of the handle (12) ans secure in position
using the two screws (24) provided.
Note: Do not overtighten these screws - light
pressure will be sufficient to hold the switch
box in position.
Finally, secure the electrical supply cable
to the lower handle using the cable clip
(17) supplied.
Handle operation (Fig. E)
E
The handle has three positions, two storage
(park) positions and one operating position.
Positions 1 and 3 in Fig. E are the storage
(park) positions and F is the operating range.
For storage purposes, the handle assembly
can be set to position 2 or 3, as follows:
With the handle in its working range F,
pivot the handle downwards until it
contacts the stops on the end of the
handle tube. This is the park position
2 for the handle.
The handle can be moved to a park
position 3. Push the handle upwards in
the working range F, to the top position
1. Pull the handle upwards. While still
pulling the handle upwards, pivot the
handle down towards the ground to
position 3.
Height of cut adjustment (Fig. F & G)
F
Your mower employs a manual method of
height of cut adjustment. The method
involves changing the arrangement of the
spacers fitted between the impeller and the
blade, and applies to mowers fitted with the
steel or plastic blade cutting systems which
can be purchased as an accessory.
The following procedure assumes that the
steel blade is fitted. If the plastic blade
cutting system is fitted then take blade to
mean blade carrier. The blade carrier (25) is
shown in Fig. F.
The procedure for adjusting the height of cut
is as follows:
Caution: The plastic blade cutting system has
been designed to maintain lawns at a fixed
length, not for cutting long grass. We strongly
recommend that you use the steel blade to
cut your grass to the required length, then
use the plastic blade to maintain that length.
Ensure your mower is disconnected from
the mains supply.
Place the handle assembly into position
3 (see “Handle operation”).
Turn your mower over onto its side so
that the underside of the cutter cover
is exposed.
Using a cloth placed over the blades or
heavy duty gloves to protect your hands,
grip the blade and, using the spanner
provided, loosen and remove the nut
(21) from the motor spindle. Turn the nut
in anti-clockwise direction to loosen it.
Note: If the plastic blade cutting system is
fitted then it will be necessary to grip the
blade carrier (25) firmly to prevent it from
turning (Fig. F).
G
Remove the blade nut, white washer
(26) (if supplied), spacers and blade
(21-24) and re-assemble to give the cut
height required, showing the 6 cut
heights available.
Once the cut height is selected,
re-assemble the blade, ensuring the
cutter blade (23) is assembled with the
cutting tips downwards as shown in
Fig. F and ensure the white washer
(26) is fitted to the blade nut.
Ensure the blade nut (21) is tight.
Note: Your mower is supplied with the blade
height in position E (Fig. G).
Always re-fit 3 spacers and never fit more
or your mower will become unsafe.
Carrying your mower
Disconnect your mower from the mains.
Remove the grassbox (if fitted), lower the handle to
the flat “park” position and then, holding one handle
near the pivot block and carry with the blade pointing
away from you.
How to use your mower (Fig. H & J)
!
Observe all the relevant warnings when
using your mower.
We recommend the directional method of
operation to obtain maximum cutting
performance from your mower and to reduce
the risk of the trailing extension lead from
entering the cutting path.
ENGLISH
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Black-Decker-GX302

Zoeken resetten

  • BETR. GX302 MES VERWIJDEREN. DIT LUKT ME NIET. IK KAN DE BORGBOUT SLECHTS EEN HALVE SLAG LINKS EN RECHTSOM DRAAIEN EN DAN IS ER EEN BLOKKERING, MAAR IK KRIJG HET MES NIET LOS. Gesteld op 20-5-2022 om 12:20

    Reageer op deze vraag Misbruik melden
  • Hoe krijg ik de borgschroef van het mes LOS? De schroef beweegt zich alleen een halve slag LINKS en RECHTS om maar daar blokkeert de bout.De nylon heb ik er af geslepen en heb no een 6 kantige KOP over. Nu past daar een BAKO op om de bout los te draaien. Alleen dat lukt me niet. Gesteld op 14-5-2022 om 11:31

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GX302 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GX302 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans, Spaans als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info