55617
7
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
7
ENGLISH
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
To fit the battery (6), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (10) while
at the same time pulling the battery out of the receptacle.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the the cell
temperature is below approximately 0 °C or above 60 °C.
The battery should be left in the charger and the charger will
begin to charge automatically when the cell temperature
warms up or cools down.
Plug in the charger (8) and switch on at the mains.
Insert the battery (6) into the charger. Make sure that the
battery is fully seated in the charger (8).
The charging indicator (9) will flash continuously (slowly).
The charge is complete when the charging indicator (9) lights
continuously. The charger and the battery can be left connected
indefinitely with the LED illuminated. The LED will change to
flashing (charging) state as the charger occasionally tops off
the battery charge. The charging indicator (9) will be lit as long
as the battery is connected to the plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Charging indicators
If the charger detects a problem with the battery, the charging
indicator (9) will flash at a fast rate. Proceed as follows:
Re-insert the battery (6).
If the charging indicators continues flashing at a fast rate,
use a different battery to determine if the charging process
works properly.
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 15 minutes to determine that the
battery is defective. If the battery is too hot of too cold, the
LED will aternatley blink fast and slow, one flash at each
speed and repeat.
Switching on and off (fig. C)
For your safety, this tool is equipped with a double switching
system. This system prevents starting the tool inadvertently
and will only allow operation while holding the tool with both
hands.
Switching on
Squeeze the front handle switch (1).
Push the lock-off button (3) forward using your thumb and
at the same time squeeze the trigger switch (2).
Release the lock-off button.
Switching off
Release the front handle switch (1) or the trigger switch (2).
Warning! Never attempt to lock a switch in the on position.
Hints for optimum use
Slightly tilt the tool (up to 15° relative to the line of cut) so
that the blade tips point slightly towards the hedge (fig. D1).
This will cause the blades to cut more effectively.
Start by trimming the top of the hedge. Hold the tool at the
desired angle and move it steadily along the line of cut
(fig. D2). The double-sided blade allows you to cut in
either direction.
In order to obtain a very straight cut, stretch a piece of
string along the length of the hedge at the desired height.
Use the string (11) as a guideline, cutting just above it (g. D2).
In order to obtain flat sides, cut upwards with the growth
(fig. D3). Younger stems move outwards when the blade
cuts downwards, causing shallow patches in the hedge.
Take care to avoid any foreign objects. Especially avoid
hard objects such as metal wire and railings, as these
could damage the blades (fig. D4).
Regularly oil the blades.
Consider purchasing a spare battery to extend the running
time of this tool. The catalogue number of the battery is
found in the technical data chart below.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GTC610L bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GTC610L in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info