527514
8
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
4
The handle assembly comprises the handle
tube (6), ‘T’ handle (7), which houses the
switch lever (8), safety lock-off switch (9) and
the electrical supply cable (10). A buckle
strap (11) is used to attach the electrical
supply cable to the handle tube.
The collection box assembly comprises the
collection box (12) which incorporates two
collection box support bars (13).
Assemble your raker, as follows:
Place your raker body (1) in its working
position, on a level surface.
B
Insert the handle tube (6) into your raker
body (1), locating the cross pin (17) in
the slot.
With the cross pin (17) located in the slot,
place the handle plate (18) against your
raker body (1), aligning the two screw holes,
and secure the handle plate in position
using the two screws (19) provided.
Place the ‘T’ handle (7) over the square
end of the handle tube (6) (Fig. B), with
the switch lever (8) on the right hand
side, slide the ‘T’ handle (7) down the
handle tube (6) until the holes in the ‘T’
handle and the handle tube are aligned.
Note: If you have any difficulty in inserting the
handle tube into the ‘T’ handle , loosen each
of the two screws at the end of the ‘T’
handle sufficiently to allow this. When
assembled, re-tighten the screws.
Fix the hexagon nut (20) into the
hexagonal recess on the underside of the
‘T’ handle, loosen each of the two
screws at the end of the ‘T’ handle (7)
and handle tube (6) and screw firmly into
the hexagon nut (20).
Secure the electrical supply cable (10) to
the handle tube (6) using the buckle
strap (11) provided.
C
Place the collection box (12) upside
down on a level surface, pass the
longest part of one of the collecting box
support bars (13) through the holes in the
side of the collection box (12), then rotate
the collection box support bar (13) in the
direction of the arrow until it clips into the
retainer on the collection box (12).
Repeat this to fit the second collection
box support bar (13).
D
With your raker in its working position, fit
the collection box (12) on to your raker
body (1), locating the collection box
support bars (13) into the pockets (22) at
the front of your raker.
The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to
their respective points in the plug (see
below). Brown is for “Live” (L) and blue is
for “Neutral” (N).
Before replacing the top cover of the
mains plug ensure that the cable restraint
is holding the outer sheath on the cable
firmly and that the two leads are correctly
fixed at the terminal screws.
Fit a
BS1363A
approved
plug
Connect blue
to N (neutral)
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
Fit the
recommended
fuse
Connect brown
to L (live)
240 volts AC only.
Never use a light
socket
!
Warning! Never connect live or neutral wires
to the earth pin marked “E” or .
Note: Do not wire an extension cable directly
into your raker yourself. Instead, take your
raker to your nearest Black & Decker
service agent.
Increased safety can be obtained by having
a qualified electrician install a high sensitivity
(30mA) circuit breaker in the house wiring.
If you do not have such a circuit breaker
installed, or you do not wish to have one
installed, then we strongly recommend that
the electrical power to your raker be supplied
through a high sensitivity residual current
device (RCD). The RCD is designed to
provide a high degree of personal protection
against harmful electric current should fault
conditions occur.
!
Warning! The use of an RCD or other circuit
breaker unit does not release the operator of
your raker from the safety instructions and
safe working practices given in this manual.
Assembly (Fig. A - D)
A
Remove all the parts of your raker from the
carton and familiarise yourself with the
individual parts of your raker.
The main parts of your raker are your raker
body (1) which houses the motor, front
wheels (2), tine assembly (3), and the rear
roller (4), which incorporates the three-
position height adjusters (5).
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GD200 verticuteermachine bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GD200 verticuteermachine in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info