15914
17
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
Always use the tool with the side handle
properly assembled.
Loosen the side handle.
For RH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the left.
For LH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the right.
Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
Insert the required drill bit.
Slacken the side handle (4).
Fit the depth adjustment rod (5) through the hole
in the side handle clamp.
Adjust the drilling depth as shown.
Tighten the side handle.
Forward/reverse slider (fig. F)
Push the forward/reverse slider (2) to the LH-side
for forward (RH) rotation. See arrows on tool.
Push the forward/reverse slider (2) to the RH-side
for reverse (LH) rotation.
Move the forward/reverse slider (2) to the central
position to lock the switch when changing
accessories, inserting the battery pack or when
storing or transporting the tool.
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Replacing the dust cover (fig. C)
The dust cover (6) prevents dust ingress into the
mechanism. Replace a worn dust cover
immediately.
Pull back the tool holder locking sleeve (13) and
pull the dust cover (6) off.
Fit the new dust cover.
Release the tool holder locking sleeve.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and
wiring.
Apply only a gentle pressure to the tool
(approx. 5 kg). Excessive force does not
speed up drilling but decreases tool
performance and may shorten tool life.
Do not drill or drive too deep to prevent
damage to the dust cover.
Switching on and off (fig. A)
To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed
switch determines the tool speed.
To stop the tool, release the switch.
Hammer drilling (fig. A)
Select the hammer drilling mode.
Insert the appropriate SDS-plus bit. For best
results use high quality carbide-tipped bits.
Mark the spot where the hole is to be drilled.
Press the tool against the workpiece.
Switch the tool on by pressing the variable speed
switch (1). The hammer mechanism should run
smoothly and the tool should not bounce.
If necessary, increase the pressure on the switch.
Rotary drilling (fig. A)
Select the rotary drilling mode.
Proceed as described for hammer drilling. Special
SDS-plus adaptors with threaded sections are
available for use with standard 10 or 13 mm
chucks to enable straight shank bits to be used.
Never use standard chucks in the
hammer drilling mode.
Screwdriving (fig. A)
Select the rotary drilling mode.
Select the direction of rotation.
Insert the special SDS-plus screwdriving adaptor
for use with hexagonal screwdriver bits.
Insert the appropriate screwdriver bit into the
adaptor. When driving slotted head screws
always use bits with a finder sleeve.
Gently press the variable speed switch (1) to
prevent damage to the screw head. In reverse
(LH) rotation the tool speed is automatically
reduced for easy screw removal.
When the screw is flush with the workpiece,
release the variable speed switch to prevent the
screw head from penetrating into the workpiece.
ENGLISH
en - 6 21
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BHA24 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BHA24 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info