53651
3
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
3
ENGLISH
Principle of operation
The power inverter converts power in two stages. The first
stage is a dc-to-dc conversion process that raises the low
voltage dc at the inverter input to 145 Vdc. The second stage
is the actual inverter stage that converts the high voltage dc
into 230 Vac, 50 Hz.
The dc-to-dc converter stage uses modern high-frequency
power conversion techniques that have replaced the bulky
transformers found in less technologically advanced models.
The inverter stage uses advanced power MOSFET transistors
in a full bridge configuration. This ensures excellent overload
capability and the ability to operate reactive loads like small
induction motors.
The power inverter output waveform
The ac output waveform of the power inverter is known as a
"modified sine wave".
This type of waveform is suitable for most ac loads, including
linear and switching power supplies used in electronic
equipment, transformers and motors.
Operating instructions
Power source requirements
The power source must provide 12.5 Vdc and must be able to
supply the necessary current to operate the load.
Warning! The power inverter must be connected only to
batteries with a nominal output voltage of 12 volts. The
appliance will not operate from a 6 volt battery and will sustain
permanent damage if connected to a 24 volt battery.
Connection to a power source
The power inverter comes equipped with a 12 Vdc accessory
plug (4) and battery clamps (5) for connection to a dc power
source.
Connecting to a power source using the 12 Vdc
accessory plug
The 12 Vdc accessory plug (4) is suitable for operating the
power inverter at power outputs up to 100 Watts. The tip of
the plug is positive (+) and the side contact is negative (-).
Warning! Connect the ring terminals to the terminals (7) of the
power inverter before connecting the accessory plug to the
accessory outlet. Make sure that the On/Off switch (3) is turned
off (O) and that no flammable fumes are present in the
installation area.
X Connect the ring terminal of the red cable to the red
terminal (7) marked (+) on the back of the power inverter.
X Connect the ring terminal of the black cable to the black
terminal (7) marked (-) on the back of the power inverter.
X Connect the power inverter to the power source by
inserting the 12 Vdc accessory plug (4) firmly into the
accessory outlet of a vehicle or other dc power source.
Warning! You must connect directly to the power source when
operating above 100 watts.
Warning! Do not use with positive ground electrical systems,
(i.e. older vehicles).
Warning! A reverse polarity connection will result in a blown
fuse and may cause permanent damage to the power inverter.
Run times
With a typical vehicle battery, a minimum operating time of
2 to 3 hours can be expected. In most instances, 5 to 10 hours
of operating time is achievable. However, the manufacturer
recommends that the operator start the vehicle every half
hour to recharge the battery system. This will guard against
any unexpected shut-down of the equipment and will ensure
that there is always sufficient battery capacity to start the
vehicle's engine.
The power inverter may be used whether or not the vehicle's
engine is running. However, the power inverter may not
operate while the engine is starting because the battery
voltage can drop substantially during cranking.
The power inverter draws less than 0.7 amperes from the
battery when it is not supplying power to a load and the On/
Off switch (3) is on (I). In most instances, the power inverter
can be left connected to the battery when not in use since it
draws very little current. However, if the vehicle is to remain
unused for several days, disconnect the power inverter from
the battery.
Rated versus actual power requirements of equipment
Most electrical tools, appliances and audio/video equipment
have labels that indicate the power consumption in amps or
watts. Be sure that the power consumption of the item you
wish to operate is rated at 400 watts or less.
The power inverter is fitted with overload protection and will
shutdown if a load in excess of 400 W is applied.
Resistive loads (i.e incandescent lights) are the easiest for
the power inverter to run.
Larger resistive loads, such as electric stoves or heaters,
usually require more wattage than the appliance can deliver
on a continuous basis.
Inductive loads, such as TV's and stereos, require more
current to operate than do resistive loads of the same
wattage rating. Induction motors, as well as some
televisions, may require 2 to 6 times their wattage rating to
start up.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BDV066 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BDV066 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info