578008
5
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
5
ENGLISH
Assembly
Warning! Make sure that the tool is switched off.
Fitting the batteries (fig. A)
Remove the battery cover (6) from the tool.
Insert the batteries into the tool in the orientation as shown.
Refit the cover and let it click into place.
Installing the tool (fig. B)
The tool can be installed on a horizontal surface such as a
floor or a table. To optimise the length of the laser line,
the tool must be installed onto its bracket. Alternatively,
the tool can be mounted to a wall.
Fitting the tool to the mounting bracket
Install the unit by clinging the bottom to the magnet (7).
To remove the unit from the bracket, pull the unit off.
Wall mounting (fig. B & C)
The round plate in the bottom of the wall mount rotates to
three positions in order to facilitate wall mounting using a
screw (I), a small nail (II), or an adhesive strip (III).
Keyhole wall mount
The keyhole wall mount (8) is used for mounting to most wall
constructions.
Drive a screw or nail into the wall.
Rotate the plate (9) into position (I).
Hang the bracket onto the fastener by the keyhole (8).
Fit the tool to the bracket.
Wall pin
If the unit is mounted to drywall or other soft materials, a wall
pin must be used:
Rotate the plate (9) into position (II).
Hold the bracket against the wall.
Drive a small nail through the hole into the wall.
Fit the tool to the bracket.
Adhesive strip
If the unit is mounted to surfaces where screws or nails
cannot be used, a removable adhesive adhesive strip must be
used. Adhesive strips can be obtained from your local retailer.
Warning! Test the strip on an inconspicuous area to make
sure it does not damage the surface material.
Rotate the plate (9) into position (III).
Peel the protective foil from one side of the strip.
Stick the strip to the bracket.
Peel the protective foil from the other side of the strip.
Press the bracket with the strip to the wall.
Fit the tool to the bracket.
To remove the strip, proceed as follows:
Remove the tool from the bracket.
Hold the bracket with one hand and grasp the end of the
adhesive strip with the other hand.
Slowly stretch the strip parallel to the wall and away from
the bracket, until the entire strip has released.
Dispose of the strip.
Use
Install the tool as required.
Switch the tool on.
Adjust the position of the tool as necessary to position
the laser lines. Be aware that extreme temperature
changes may affect the adjustment of the unit.
After finishing work, always switch off the tool.
Switching on and off
To switch on, slide the switch (1) into position I.
To switch off, slide the switch (1) into position 0.
Levelling the laser lines (fig. D & E)
When projecting laser lines in horizontal applications,
adjust the unit as necessary until the vials (4) are level.
When projecting laser lines in vertical applications, adjust
the unit as necessary until one of the vials (4) is level.
Using the scale
The scale (5) can be used to transfer a square angle.
Position the unit with the laser lines at the starting point.
Align the 0° position on the scale with one of the laser
beams.
Holding the bracket (3) with one hand, position the tool
with the other hand as necessary.
Cleaning and maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
To clean the tool, use only mild soap and a damp cloth.
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BDL90 T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BDL90 T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info