578007
5
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
5
ENGLISH
Fig. A
7. On/off switch (measurer)
8. Set key
9. Repeat measurement key
10. Spacing key
11. Reset key
Fig. B
12. Wallpin
13. Keyhole wall mount
Assembly
Fitting the battery (fig. C)
Remove the battery cover (14) from the tool.
Insert the batteries into the tool in the orientation as shown.
Refit the cover and let it click into place.
Wall mounting (fig. B & D)
The tool can be mounted to walls using one of the wall
mounts (12 or 13).
Wall pin
If the tool is mounted to drywall or other soft materials, the
wall pin (12) must be used. The position of the laser line will
line up with the mounting location of the pin.
Remove the protective cap (15) from the pin (16) and store
it on the insert as shown (fig. D).
Hold the wall pin at the required height in front of a
suitable location and press the pin straight into the wall.
Install the tool by hanging the holder (4) on the wall mount.
Warning! The pin of the insert is sharp and should be
handled with care. Replace the protective cap immediately
after removing the insert from the wall.
Keyhole wall mount
For surfaces other than drywall, the keyhole wall mount (13)
can be used with a screw in a predrilled hole. The position of
the laser line will line up with the mounting location of the screw.
Hang the wall mount on a screw mounted at the required
height on a suitable location.
Install the tool by hanging the holder (4) on the wall
mount.
Use
Using the laser level function (fig. E & F)
Using the laser in auto-leveling mode
Hang the tool on the wall using the appropriate wall mount.
Push the on/off switch (1) up to switch the tool on in auto-
leveling mode.
The auto levelling indicator (17) will light up and swing while
the tool is calibrating.
Note: the laser lines will only be level if the tool is kept within
5° from vertical.
Push the on/off switch (1) down to switch the tool off.
Using the laser in locked/layout mode
When operating in the locked/layout mode, the tool can be
held in horizontal position, for surface layout such as flooring
and tiling.
Place the tool flat on the floor.
Push the on/off switch (1) down to switch the tool on in
locked/layout mode. The locked/layout indicator (18) will
light up.
Move the tool as necessary to position the laser lines.
Push the on/off switch (1) up to switch the tool off.
Using the measurer function
Switching on and off (fig. A)
To switch the tool on, press key (7).
To switch the tool off, press key (7) again.
Setting the reference point (fig. A, E & G)
The reference point is the part of the tool that the measurement
starts from and ends at. The reference point can be aligned
with the left (19), the right (20) or the centre (21) of the tool.
For accurate results, the reference point can be set before and
after the measurement.
To set the reference point, press either of keys (8).
Selecting the measurement system (fig. A & E)
The appliance can show the results both in the metric (22) and
the imperial system (23).
To switch from one measurement system to the other,
press and hold key (7) for 4 seconds.
Measuring (fig. A & E)
Place the tool flat against the wall at the start of the
distance to be measured. Switch the tool on.
Press and hold key (11) for 4 seconds. The ready-for-use
indicator (24) will light up.
Set the reference point indicating the start of the
measurement.
Slowly slide the tool along the distance to be measured.
Make sure not to tilt or lift the tool.
Set the reference point indicating the end of the
measurement.
To reset the tool, press and hold key (11) for 4 seconds.
Wait for the ready-for-use indicator (24) to light up before
continuing.
Note: After 2 minutes of inactivity the LCD screen will go blank.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BDL500M T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BDL500M T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,99 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker BDL500M T1

Black Decker BDL500M T1 Gebruiksaanwijzing - Türkiye - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info