578005
5
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
5
ENGLISH
Additional safety instructions for pipe and wire detectors
Do not use the tool to detect AC voltage in uninsulated,
exposed or free wires.
Do not use the tool as a substitute for a voltmeter.
Be aware that the tool may not always properly detect all
pipes and wires. The following conditions can cause
inaccurate results:
Low battery
Thick walls with thin pipes or wires
Very thick walls
Very deep wires or pipes
Walls covered with metal
Very humid conditions
Shielded cables
Before use, always test the tool by detecting a known
pipe or wire.
If in doubt contact a qualified contractor.
Warning! This tool will not detect wires in circuits isolated
from the mains supply, cables operating at direct current (DC)
or wires used for telecommunication or computer systems.
Hidden wires (e.g. wall lights) may not be detected when
switches are in the off position.
Warning! This tool will not detect pipes of any other material
than metal.
Features
1. On/off switch (laser)
2. On/off switch (stud/metal finder)
3. Mode selector key
4. LCD screen
5. LED indicator (wire detector)
6. Wall mount holder
7. Laser apertures
Fig. A
8. Wallpin
9. Keyhole wall mount
Assembly
Fitting the battery (fig. B)
Remove the battery cover (10) from the tool.
Insert the batteries into the tool in the orientation as shown.
Refit the cover and let it click into place.
Wall mounting (fig. A & C)
The tool can be mounted to walls using one of the wall
mounts (8 or 9).
Wall pin
If the tool is mounted to drywall or other soft materials,
the wall pin (8) must be used. The position of the laser line
will line up with the mounting location of the pin.
Remove the protective cap (11) from the pin (12) and store
it on the insert as shown (fig. C).
Hold the wall pin at the required height in front of a
suitable location and press the pin straight into the wall.
Install the tool by hanging the holder (6) on the wall mount.
Warning! The pin of the insert is sharp and should be
handled with care. Replace the protective cap immediately
after removing the insert from the wall.
Keyhole wall mount
For surfaces other than drywall, the keyhole wall mount (9)
can be used with a screw in a predrilled hole. The position of
the laser line will line up with the mounting location of the screw.
Hang the wall mount on a screw mounted at the required
height on a suitable location.
Install the tool by hanging the holder (6) on the wall mount.
Use
Using the laser level function (fig. D & E)
Hang the tool on the wall using the appropriate wall mount.
Push the on/off switch (1) up to switch the tool on.
The auto levelling indicator (13) will light up and swing while
the tool is calibrating.
Note: the laser lines will only be level if the tool is kept within
5° from vertical.
Push the on/off switch (1) down to switch the tool off.
Selecting the operating mode (fig. D)
The operating mode is indicated on the display (4).
For the detection of studs, press the mode selector key (3)
as necessary until the ‘STUD’ position (15) is selected.
For the detection of metal studs, pipes, etc., press the
mode selector key (3) as necessary until the ‘METAL’
position (16) is selected.
Using the stud finder function (fig. D & F)
You can use this function to find wooden and metal studs
through drywall boards up to 19 mm thick.
Set the required operating mode.
Place the tool flat against the wall as shown.
Keep the on/off switch (2) depressed.
The scanner bars (17) will light up and the buzzer will sound
once while the tool is calibrating. After calibration is
completed (18):
Slowly slide the tool in a horizontal direction. Make sure
not to tilt or lift the tool.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BDL230S T1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BDL230S T1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker BDL230S T1

Black Decker BDL230S T1 Gebruiksaanwijzing - Polski - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info