709470
9
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
8
ENGLISH
(Original instructions)
9
ENGLISH
(Original instructions)
Lower Blade Guard
WARNING: Laceration Hazard. The lower blade guard is
a safety feature which reduces the risk of serious personal
injury. Never use the saw if the lower guard is missing, dam-
aged, misassembled or not working properly. Do not rely on
the lower blade guard to protect you under all circumstances.
Your safety depends on following all warnings and precautions
as well as proper operation of the saw. Check lower guard for
proper closing before each use as outlined in Additional Safety
Rules for Circular Saws. If the lower blade guard is missing
or not working properly, have the saw serviced before using.
To assure product safety and reliability, repair, maintenance
and adjustment should be performed by an authorized service
center or other qualied service organization, always using
identical replacement parts.
WARNING: To minimize the risk of eye injury, always use eye
protection. Foreign objects in the work place such as wire or
nails can cause tips to crack or break. Only operate saw when
proper saw blade guard is in place. Mount blade securely in
proper rotation before using, and always use a clean, sharp
blade.
WARNING: To reduce the risk of injury, It is important to
support the work properly and to hold the saw rmly to prevent
loss of control which could cause personal injury. Figure E
illustrates typical hand support.
Use.
WARNING: To reduce the risk of serious personal injury,
read, understand and follow all important safety warnings and
instructions prior to using tool.
Blade Selection
Your circular saw is designed for use with 140 x 2 mm diam-
eter blades that have a 12.7 mm diameter bore. Blades must
be rated for 7000 RPM operation (or higher). DO NOT use any
abrasive wheels.
General Cuts
WARNING: To reduce the risk of injury, remove the battery,
and follow all assembly, adjustment and set up instructions.
Make sure lower guard operates. Select the proper blade for
the material to be cut.
u Measure and mark work for cutting.
u Support and secure work properly (See Safety Rules and
Instructions).
u Use appropriate and required safety equipment (See
Safety Rules).
u Secure and maintain work area (See Safety Rules).
u With battery inserted, make sure switch turns saw on and
off.
Switch
Saw is equipped with a switch lock-off feature to prevent
unintentional operation.
u To operate the tool, press in on the lock-off button (2) from
either side of the saw and hold it in as you depress the
trigger switch (3).
u After you have depressed the trigger and the tool is run-
ning, release the lock-off button.
u The tool will continue to run as long as the trigger is
depressed.
u To turn the tool off, release the trigger switch.
NOTE: This tool has no provision for locking the tool on, and
the switch should never be locked on by any other means.
Automatic Electric Brake
Your saw is equipped with an electric blade brake which stops
the saw blade within 1-2 seconds of trigger release. This is
automatic and requires no adjustment.
Sawing
WARNING:
To reduce the risk of serious personal injury,
always hold the tool with both hands.
u Let the blade run freely for a few seconds before starting
the cut.
u Apply only a gentle pressure to the tool while performing
the cut.
u Work with the shoe pressed against the workpiece.
Hints for optimum use
u As some splintering along the line of cut on the top side of
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
u Where splintering is to be minimized, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
Pocket cutting (g. K)
WARNING: Never tie the blade guard in a raised position.
Never move the saw backwards when pocket cutting. This
may cause the unit to raise up off the work surface which
could cause injury.
A pocket cut is one that is made when the edge of the
material does not push the lower guard open, but the bottom
edge of the rotating blade cuts into the middle of the material.
u Adjust the shoe (5) so the blade cuts at desired depth.
u Tilt the saw forward and rest front of the shoe on
material to be cut.
u Using the retracting lever, retract lower blade guard to
an upward position. Lower rear of shoe until blade teeth
almost touch cutting line.
u Release the blade guard (its contact with the work will
keep it in position to open freely as you start the cut).
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BDCCS18 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BDCCS18 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info