709548
5
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
5
ENGLISH
(Original instructions)
Chargers
u
Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u
Never attempt to charge non-rechargeable batteries.
u
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
Do not attempt to charge damaged batteries.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Features
This tool includes some or all of the following features:
1. On/off switch
2. Forward/reverse slider
3. Bit holder
4. LED work light
5. Charging port
6. Charger
7. USB connector
8. Bit storage
9. Case
10. Case insert
Chargingthebattery(fig.A,B)
u
Insert the USB connector (7) into the charging port (5).
u
Plug in the charger (6).
u
Leave the tool connected to the charger for 1 hour.
u
The charging indicator (5a) will illuminate during charging.
u
The tool can also be charged while it is in the case (9), as
illustrated in figure B.
Fitting and removing a screwdriver bit (fig.C)
This tool uses screwdriver bits a 6.35 mm hexagonal shank.
u
To t a bit, insert the bit shaft (8) into the bit holder (3).
u
To remove a bit, pull the bit shaft (8) out of the bit holder
(3).
LEDworklight(g.D)
The LED work light (4) is activated automatically when the on/
off switch (1) is depressed. The LED will also illuminate when
the trigger is depressed and the forward/reverse slider (2) is in
the locked off position (central position).
Selectingthedirectionofrotation(fig.E)
For tightening screws, use forward rotation. For loosening
screws use reverse rotation.
u
To select forward rotation, push the forward/reverse slider
(2) to the forward position.
u
To select reverse rotation, push the forward/reverse slider
(2) to the rearward position.
u
To lock the tool, set the forward/reverse slider into the
centre position.
Screwdriving
u
Select forward or reverse rotation using the forward/
reverse slider (2).
u
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch (1).
Hints for optimum use
Screwdriving
u
Always use the correct type and size of screwdriver bit.
u
If screws are difcult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u
Always hold the tool and screwdriver bit in a straight line
with the screw.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any cleaning or maintenance on
the tool, unplug the charger.
u
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BCF611C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BCF611C in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info