577843
15
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
03/ 2012
BENNING SUN 2
13
8.2.2 Starting / stopping the data logger
- Press the key
7
(LOG) for > 5 seconds to activate the data logger. Display: "LOG".
- Press the key
7
(LOG) again and then the key
7
(OK) to confirm "run". The measured
values are written into the internal memory including a time / date stamp. The digital display
2
goes out and the device switches over into the energy-saving stand-by mode.
- Press any key to display the progress of the data logger. The digital display briefly goes on
and then goes out again.
- If you want to stop the data logger, press any key to display the data logger. Press the key
7
(LOG) and then the key
7
(OK) to confirm "StOP".
- Press the key
3
or
4
to exit the data logger.
8.2.3 Reading out the data logger via the USB interface
- Install the driver and the download software from the CD-ROM once.
- Connect the BENNING SUN 2 to your PC by means of the USB connecting cable and switch
the device ON.
- Start the download program, go to "Tools" and click "Refresh Ports".
- Select the COM port used and click "Download".
- The download of measured values starts.
Troubleshooting:
- One of the most frequent connection errors is the selection of the wrong COM port.
- If the measured values are not downloaded, verify the COM port used by means of the
Device Manager of your system.
- As soon as the BENNING SUN 2 has been connected to your PC by means of the USB
connecting cable, the hardware driver and thus the COM port used can be viewed in the
Device Manager under "Ports (COM & LPT)", e.g. Silicon Labs CP210x USB to UART
Bridge (COM14).
8.2.4 Setting the date and the time
- Press the key
5
to display the time / date on the digital display
2
.
- Press the key
5
again for > 5 seconds until the hour display starts ashing.
- Press the ► key
3
to select the time / date eld (eld is ashing).
- Press the ▲ key
4
or ▼ key
5
to increase or decrease the value.
- Press the key
7
(OK) to store the setting.
time / 24-hour display
day / month
year
8.2.5 Changing the displayed unit
- Press the
3
key for > 5 seconds until the displayed temperature unit starts flashing.
- Press the ►
3
key to select the respective unit for insolation or temperature.
- Press the ▲
4
or
5
key to change between the units °C or °F or between the units W/m²
or BTU/hr/ft².
- Press the
7
key (OK) to store the setting.
9. Maintenance
Do not open the device. It does not contain any components requiring maintenance by the user.
Repair and service must be carried out by qualied personnel only!
9.1 Cleaning
Clean the exterior of the device with a clean dry cloth (exception: special cleaning wipers). Do not
use any solvents or abrasives to clean the device. Make sure that the battery compartment and
the battery contacts are not contaminated by leaking battery electrolyte.
If there are electrolyte contamination or white deposits in the area of the battery or the battery
housing, clean these areas as well by means of a dry cloth.
9.2 Battery replacement
The BENNING SUN 2 is supplied by means of two 1.5 V batteries of type AA (IEC LR6).
It is necessary to replace the batteries as soon as the battery voltage falls below 1.8 V (see
section 8.1.2).
Proceed as follows to replace the battery:
- Switch the BENNING SUN 2 off.
- Put the BENNING SUN 2 face down and slide the battery compartment cover off the bottom
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Benning SUN 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Benning SUN 2 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Benning SUN 2

Benning SUN 2 Snelstart handleiding - Nederlands, Deutsch, English, Français, Italiano, Espanõl - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info