577840
27
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
09/ 2012
BENNING PV 1-1
21
The electronic components of the BENNING PV 1-1
have reached the maximum admissible temperature.
Disconnect the BENNING PV 1-1 from the object to
be measured and let it cool down.
The DC short-circuit current exceeds the maximum
value of 10 A. Measurement has been stopped.
The DC open circuit voltage has exceeded the ma-
ximum value of 1000 V. The measurement has been
stopped.
The BENNING PV 1-1 is not correctly calibrated, see
chapter 9.6 "Calibration".
etc.
Please return the BENNING PV 1-1 to an authorized
service center, see chapter 9.6 "Calibration" for the
address.
Please return the BENNING PV 1-1 to an authorized
service center, see chapter 9.6 "Calibration" for the
address.
Please return the BENNING PV 1-1 to an authorized
service center, see chapter 9.6 "Calibration" for the
address.
or
Please return the BENNING PV 1-1 to an authorized
service center, see chapter 9.6 "Calibration" for the
address.
9.2 Securing the instrument
Under certain circumstances safe operation of the BENNING PV 1-1 is no longer ensured, for
example in the case of:
- Visible damage of the casing.
- Incorrect measurement results.
- Recognisable consequences of prolonged storage under improper conditions.
- Recognisable consequences of extraordinary transportation stress.
In such cases the BENNING PV 1-1 must be switched off immediately, disconnected from the
measuring points and secured to prevent further utilisation.
9.3 Cleaning
Clean the casing externally with a clean dry cloth (exception: special cleaning wipers). Avoid
using solvents and/ or scouring agents for cleaning the instrument. It is important to make sure
that the battery compartment and battery contacts are not contaminated by leaking electrolyte.
If electrolyte contamination or white deposits are present in the region of the batteries or battery
casing, clean them too with a dry cloth.
9.4 Battery replacement
c
Before opening the BENNING PV 1-1, make quite sure that it is voltage free!
Electrical danger!
The BENNING PV 1-1 is supplied by six 1.5 V batteries/ type AA (IEC LR6).
A battery change (see Figure 9) is required, if the battery symbol P appears in the display unit
1
.
Proceed as follows to replace the batteries:
- Switch the BENNING PV 1-1 off.
- Put the BENNING PV 1-1 face down and unscrew the screw of the battery compartment
cover.
- Lift off the battery compartment cover (in the area of the housing slots) from the bottom part
of the battery compartment.
- Remove the discharged batteries from the battery compartment.
- Then, insert the batteries into the battery compartment at the provided places (please ob-
serve correct polarity of the batteries).
- Lock the battery compartment cover into place on the bottom part and tighten the screw.
See gure 9: Battery/ fuse replacement
m
Make your contribution to environmental protection! Do not dispose of
discharged batteries in the household garbage. Instead, take them to a
collecting point for discharged batteries and special waste material. Please
inform yourself in your community.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Benning PV 1.1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Benning PV 1.1 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 10,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Benning PV 1.1

Benning PV 1.1 Snelstart handleiding - Nederlands, Français, Italiano, Espanõl - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info