656678
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
ULTRAZONE ZMX8210
Installation8
Connect the potentiometer to pins V and SHD. Connect the mid
tap to pin C (see Fig. 3.2).
Volume potentiometer
Remote volume control Fig. 3.2:
connection with potentiometer
Alternatively, you can control the volume by using a positive con-
trol voltage of max. 11 V DC. The voltage needs to be inserted
between the pins SHD and C.
When using a voltage source to remote control the vol- +
ume level, make sure that the control voltage does not
exceed 11 V DC or else your unit could be damaged.
Selecting stereo channels 7 and 8
To select the stereo channels 7 and 8, you need a push-button
switch and optionally two LEDs.
Connect the push-button switch to pins SHD and SEL. You can
add two LEDs to indicate the selected channel. They have to be
connected in parallel with a reverse polarity between the pins IND
and SHD (see Fig. 3.3).
Control LED CH 8
Control LED CH 7
Channel select switch
Connection with push-button switch and two LEDs for Fig. 3.3:
channel selection
Basic operation3.2
Using the ZMX8210 is easy to learn and is very similar to using a
standard mixer. Complete the following steps:
Hook up the unit as described in Chapter 3.1.1)
Adjust the LEFT, RIGHT and AUX LEVEL knobs 2) [17] to center
position and turn the LEVEL knobs {5} of each channel fully
to the left.
Turn on the ZMX8210 and the other devices you want to use 3)
(amplier and loudspeakers last).
Apply an audio signal (line or microphone signal) to an input 4)
channel.
Press the +48 V push-button switch 5) {2} in case you want to
use a capacitor microphone.
Press the push-button switches L, R and AUX 6) {3} to select
the buses to which the input signals are sent.
Turn the LEVEL knob of the corresponding channel to the 7)
right until
you have reached the required volume level =
or the 0 db LED glows continuously. =
If the CLIP LED lights up, you need to adjust the level by slowly
turning the knob to the left. For especially strong input signals, use
the PAD push-button switch {1} to attenuate the signal further.
Repeat steps 4 to 7 with additional signal sources. Use chan-8)
nels 7 or 8 for stereo signal sources.
In case you are using a microphone, press the MIC LOW CUT 9)
push-button switch [11] to reduce low-frequency rumble such
as subsonic noise.
Press the EQ ON push-button switch 10) [14] and adjust the LOW,
LOW MID, HIGH MID and HIGH knobs of the equalizer section
(15) to modify the sound.
Use the LEVEL knobs of the LEFT, RIGHT and AUX buses 11)
[17] to adjust the volume level of the OUT L, OUT R and AUX
outputs (zones).
Installation4.
Rack mounting4.1
The unit requires the height of 1 U to t within a 19" rack. Please
make sure to provide approximately 4" of space for the connec-
tors on the rear panel. Please use M6 rack screws and nuts when
rack-mounting the unit.
Audio connections4.2
The ZMX8210 connections are Euro-type connectors. You require
special PCB connectors for the cabling. You can purchase the
connectors at well-assorted electronics retailers. The ZMX8210
connectors' pin assignment is printed on the rear panel of the unit.
Alternatively, refer to the following diagrams.
INPUTS / AUX / OUT R / OUT L
Pin assignment of the INPUTS connectorsFig. 4.1:
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Behringer ZMX8210 Ultrazone bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Behringer ZMX8210 Ultrazone in de taal/talen: Engels als bijlage per email.

De handleiding is 1,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Behringer ZMX8210 Ultrazone

Behringer ZMX8210 Ultrazone Gebruiksaanwijzing - Nederlands - 9 pagina's

Behringer ZMX8210 Ultrazone Gebruiksaanwijzing - Deutsch - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info