660595
5
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
5 PRO MIXER VMX100USB User Manual
2.1 Input channels 1 and 2
(1) The PHONO/LINE-USB switch selects one of the input pairs on the
respective channel. The “PHONO” setting (and inputs) are intended for
turntables; for all other signal sources, i.e. a CD or MD player, use the “LINE
setting and inputs. Audio sent from a computer to the VMX via USB cable is
routed to channel 1. This signal is mixed with the LINE input.
Never connect line-level equipment to the highly sensitive phono
inputs! The output levels of phono cartridge systems are in the
millivolt range, whereas CD and MD players, as well as tape decks,
provide outputs levels in the volt range. In other words, the level of line
signals is up to 100 times higher than phono output levels.
(2) The GAIN control is used to adjust the input signal level.
The overall level of your signal is also effected by the EQ settings.
Its a good idea to adjust the equalizer before you set the level with the
GAIN control.
(3) Each of the two input channels is equipped with a 2-BAND EQUALIZER
with kill characteristic. The maximum amount of attenuation (-32 dB) is
much higher than the maximum boost (+12 dB), allowing entire frequency
spectrums to be “removed” from a track.
(4) The CHANNEL fader adjusts the nal channel volume.
2.2 PFL section (Pre Fader Listening)
The PFL signal is a pre-fader headphones signal, enabling you to pre-listen to a
signal source without eecting the main signal.
(5) The LEVEL control determines the volume of the headphones signal.
(6) The MIX control lets you fade between channels 1 and 2.
(7) The LEVEL METER displays the level of the signal selected via the
MAIN/PFL button ((8)).
(8) The MAIN/PFL button allows you to route either the main or PFL signal to
the display. Remember: “PFL” is your pre-listening or headphone signal and
“MAIN” is the signal assigned to the outputs of the VMX100USB.
In PFL mode, the channel 1 signal is displayed on the left side of the
LEVEL METER, and channel 2 on the right.
2.3 Mic/Main section
(9) The MAIN knob controls the overall output volume.
(10) The MIC LEVEL control adjusts the volume of the microphone signal.
2.4 Beat counter
The PRO MIXER VMX100USB’s built-in beat counter is an extremely useful feature,
allowing smooth crossfades between two tracks—an important key to the
success of your performance. The beat counter analyzes and displays the tempi
of your tracks in BPM (Beats Per Minute). The beat counter sections of channel
1 and 2 are identical.
The tempo of the track is shown in the respective channels Display ((11)).
In the case of multiple tempo changes, the display would change continuously,
causing unnecessary confusion and rendering the function virtually useless.
Enter the SYNC LOCK button ((12)): with it, you can limit the range of possible
tempo values within a song. Pressing this button once the counter has “caught
and displayed a realistic value will simplify things. The BEAT ASSIST button ((13))
allows you to set the beat counters tempo manually, similar to“tap tempo”.
Pressing the button three times in time with the track will set the beat counter
and its display at that tempo. The BEAT ASSIST and SYNC LOCK buttons are each
equipped with an LED to show that the respective function is activated.
Once the tempo of the two tracks have been determined and locked with the
SYNC LOCK or BEAT ASSIST buttons, the tempo dierence between channel 1
and 2 will be depicted via the 9-segment TEMPO DIFFERENCE LED display ((14)).
It shows the degree of the tempo dierence by a respective deection to the
right (channel 2 track is faster) or to the left (channel 2 track is faster). The center
LED lights when the tempi are equal. The synchronization of channel 1 and 2 is
shown in the TIME OFFSET LED display ((15)) below the TEMPO DIFFERENCE display.
When the center LED is lit, the tracks are in sync with each other. When the
display moves to the left or right, the corresponding channel is running out of
sync. The TEMPO DIFFERENCE and TIME OFFSET displays are only active when the
tempi of both channels have been locked as explained above.
To exit the SYNC LOCK or BEAT ASSIST mode, simply press the SYNC LOCK key in
both channels again.
2.5 Crossfader section
(16) The CROSSFADER is used to fade between channels 1 and 2.
(17) The CURVE switch, located on the left side of the CROSSFADER, enables you
to select between two crossfade modes: SOFT and SHARP. In SOFT mode
the crossfader fades between the channels in a linear, continuous manner.
This mode is recommended for slower, smoother crossfades. In SHARP
mode the crossfader takes on a more logarithmic eect, working faster
towards the outer edges of the fader range. Use this mode for faster,
“hard” crossfades.
Flipping the CURVE switch may cause a sudden change in volume.
We recommend not changing this setting while a signal is present.
(18) The MIC INPUT connector is a balanced ¼" TRS socket for
microphone connection.
We strongly recommend the use of high-grade cables and connectors
for the transmission of audio signals. Inferior quality materials cannot
supply acceptable audio quality or corrosion protection.
(19) The HEADPHONES socket allows you to connect your headphones for
pre-listening (PFL signal). For best results, use headphones with an
impedance rating of at least 32 Ohms.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Behringer VMX100USB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Behringer VMX100USB in de taal/talen: Engels als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Behringer VMX100USB

Behringer VMX100USB Snelstart handleiding - Deutsch, English, Français, Português, Espanõl - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info