306032
28
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
Troubleshooting Guide
Depending on the model, your
washing machine is equipped
with various automatic safety
functions. This enables faults to
be detected in good time and
the safety system can react
appropriately.
These faults are frequently so
minor that they can be
removed within a few minutes.
The appliance will not
start, no display is visible.
Check whether:
the mains plug is inserted
into the socket
the wall socket is functioning
correctly (use a table lamp or
similar) to test
the “On/Off” button has
been pressed and the
washing machine is switched
on
The washing machine will
not start and the “Start”
light is flashing.
The notice “Door Open!”
appears in the display:
close the door (child safety)
The washing machine
stops shortly after the
programme start.
The message “No Water
Supply!” appears on the
display.
Switch the washing machine
off, pull out the mains plug and
check whether:
the tap is fully turned on
the water supply pressure is
sufficient
the water inlet hose is kinked
the mesh filters are blocked
(see “Care And
Maintenance”/”Mesh Filters
in the Water Connection”)
the water in the inlet hose is
frozen
the washing machine has a
safety hose and the safety
valve is open (red indicator in
the safety valve inspection
window); In this case replace
it with a new safety hose
Reconnect the appliance to the
electrical socket. Switch the
washing machine on and
restart the desired programme
(do not add any more
detergent).
The washing machine
stops during the
programme and the
“Start” light flashes.
Check whether:
“Rinse Hold Selected
appears in the display
the door has been opened.
Close the door
Press the “Start” button to
continue with the programme
Detergent and additive
product residues in
dispenser at end of wash.
Check whether:
the siphon is correctly
installed and clean (see “Care
And Maintenance”)
sufficient water is entering.
The mesh filters could be
clogged (see Care And
Maintenance/Mesh Filters in
the Water Connection)
when using powder
detergent beforehand the
coloured insert for dosing
liquid detergent has been
removed from the
dispenser
The washing machine
vibrates during the spin
cycle.
Check whether:
the washing machine is level
and standing firmly on all
four feet
the transport bolts have been
removed. Before using the
machine, it is imperative that
the transport bolts are
removed
Final spin results are poor:
Check whether the notice
“Load Imbalance!
” or
“Excessive Foam
!” appears on
the display.
The washing machine has an
unbalance detection and
correction system. If individual
heavy items are loaded (e.g. a
bathmat or bathrobe), this
system may reduce the spin
speed automatically or even
interrupt the spin completely if
it detects too great an
imbalance even after several
spin starts, in order to protect
the washing machine
if the laundry is still too wet
at the end of the cycle, add
smaller articles of laundry
and repeat the spin cycle
excessive foam formation
may prevent spinning.
Observe correct detergent
dosages
Check whether:
spin speed “0” has been
selected
4gb15137.fm Page 10 Friday, October 10, 2003 12:56 PM
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bauknecht wal10988 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bauknecht wal10988 2 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Bauknecht wal10988 2

Bauknecht wal10988 2 Gebruiksaanwijzing - Nederlands - 38 pagina's

Bauknecht wal10988 2 Gebruiksaanwijzing - Deutsch - 30 pagina's

Bauknecht wal10988 2 Gebruiksaanwijzing - Français - 30 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info