658720
14
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
ULTRASONIC SPEED SENSOR
13
1.9.3 Attaching the safety wire
Plastic housing – Attach the wire to one eye of the hull nut. Twist the wire in a
anti-clockwise direction and thread it through one of the eyes in the cap nut,
then through the pull ring and the other eye of the cap nut, and finally through
the opposite eye of the hull nut. Twist the wire onto itself to lock the assembly.
Bronze housing – Wrap one end of the locking wire around the housing and
twist it together. Thread the other end up through the eyehole in the cap nut,
loop the wire through the pull ring and twist it securely onto itself to lock the
assembly.
Route the cables to the interface box being careful not to damage the insulation
when passing through bulkheads etc. In order to reduce electrical interference,
separate the sensor cables from electrical wiring and other sources of noise.
Immediately after putting the boat into the water, check the installation for signs
of leakage. Note that small leaks may not be readily observed. It is advised that
the boat is not left in the water for more than 3 hours before re-checking the
installation for leaks.
If leakage is observed, remove the boat from the water and repeat the
installation procedure.
Figure 1.7 - Preparation of a Cored Fibreglass Hull
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw BandG Ultrasonic Speed Sensor bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van BandG Ultrasonic Speed Sensor in de taal/talen: Engels als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info