67658
15
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
– 14 – – 15 –
Attach the ground cable to the GND terminal on the backside of the active subwoofer. In
most cases it will be best to keep the ground cable („-12V“) as short as possible, i.e. to
find a chassis contact very close to the active sub. The ground power wire must have the
same cross-section as the positive power cable. The contact point where the ground wire is
attached to, must be solid and clean, i.e. free from rust or paint!
4.2 RCA & REMOTE WIRES
Carefully run the RCA interconnect and the amp- or antenna-remote wire from your headunit
to the respective inputs on your active sub. The audio signal cables should always be routed
completely separate from the power cables.
5. CROSSOVER ADJUSTMENTS
5.1 LOWPASS X-OVER FREQUENCY
The lowpass cut-off frequency setting, marked as „CROSSOVER“ on the amp-module,
depends on some variables, i.e. the bass response of the loudspeakers installed in the car.
As a rule of thumb, settings in a range between 80 to 100 Hz will render best sonic results.
For an intermediate lowpass crossover setting to attempt input gain and phase-shift control
adjustments, go for a VR-pot set to approx. 12 o’clock and after input gain and phase
have been adjusted, it is advisable to fine tune the lowpass crossover frequency for best
possible sound quality.
Note: In general, setting the lowpass cross-over frequency too low, will result in a weak
and muddy sounding bass, while setting this crossover frequency too high will result in a
‘booming’ bass sound and reduced low end extension.
5.2 INPUT GAIN
To reach a maximum in dynamic response from each individual head-unit/amplifier/speaker
combination, it is important to set the respective input level controls („GAIN“) of the amp-
module correctly.
Before you start, you MUST set all tone controls (Bass, Mid, Treble, Loudness etc.) and the
fader on the head unit to their neutral or center positions.
Switch on your headunit, and set the playback level to a medium volume.
Now turn up the input “GAIN” on the front side of the active subwoofer, until you hear
enough bass volume. Close the trunk of your car, listen to the result and fine tune the GAIN
level by turning the pot down or up, until a good tonal overall balance with enough bass is
achieved.
5.3 PHASE-SHIFT
The phase shift function of the AB20A can not be deactivated, it is permanently in the signal
chain. The phase-shift control enables you to match the acoustical phase relations of the
active subwoofer and the speaker system of your car. A good match of the acoustical phase
between subwoofer and the system in the front doors will give you the impression of bass
coming from a place in front of you. This setting must be played entirely by ear.
AB20A Manual D+E.indd 15 04.08.2006 15:57:34 Uhr
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Axton AB20 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Axton AB20 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Axton AB20

Axton AB20 Gebruiksaanwijzing - Deutsch, English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info