6
Auto select: Press [Scan], “AUTOTUNE FULL SCAN” will appear on the display. The number of found stations will show in the
top right corner of the display. The radio will start to play the first found station automatically after completing the scan.
Rotate the [Tune/Select] knob to select another DAB station. Press [Tune/Select] to confirm.
Manual select: Press and hold the [Tune/Select] knob until “MANUAL TUNE” appears on the display. Turn the [Tune/Select]
knob to choose a station. Press [Tune/Select] to confirm.
Station presetting: While playing in DAB mode, press and hold [Preset]. “Preset Empty X” will appear on the display. Turn the
[Tune/Select] knob to select the desired preset slot (1-10), press [Tune/Select] to store.
Press [Preset] to recall memory. Turn the [Tune/Select] knob to select the stored station you want to listen to. Press
[Tune/Select] to confirm. If stations are saved in slot 1, 2 and/or 3, it’s possible to quickly recall them by pressing [1], [2] or
[3].
Show channel information: Press [Info] to show various forms of information regarding the station that is being played.
Press [Menu] to show the current software version.
To receive the ordinary FM stations (no internet connection is required), place the radio close to the window and extend the
antenna as far as it can go to get the best reception. You may need to adjust the direction of the antenna to improve
reception.
Press [Mode] to select FM mode. Press [Scan], the radio will start searching for channels. When a channel has been found, it
will be played automatically. If reception is not as desired, use the [Tune/Select] knob to manually fine tune frequency.
Station presetting: While playing in FM mode, press and hold [Preset]. “Preset Empty X” will appear on the display. Turn the
[Tune/Select] knob to select the desired preset slot (1-10), press [Tune/Select] to store.
Press [Preset] to recall memory. Turn the [Tune/Select] knob to select the stored station you want to listen to. Press
[Tune/Select] to confirm. If stations are saved in slot 1, 2 and/or 3, it’s possible to quickly recall them by pressing [1], [2] or
[3].
Show channel information: Press [Info] to show various forms of information regarding the station that is being played.
Press [Menu] to show the current software version.
Before transmission between your BT device and the radio is possible, both devices must be coupled. This process is called
"pairing". The radio is served as a receiver, to receive the music stream to be played on the radio.
If you have already coupled to a BT device before, this connection will be restored automatically when both devices are in
range and BT operation has been selected on the radio. "Pairing" does not have to be repeated. This function may need to be
activated in your BT device, however.
• Press [Mode] until “BT” shows on the display.
• Turn on BT streaming on your device. The device will scan for pairable BT devices in the reception range.
• Select “Audizio Corno” from the list with found devices.
• Start playback on your BT device. Playback now takes place emitting sound from the radio.
You can listen to the music stored in other audio device or smart phone via the radio, through the connection to the 3.5 mm
aux-in jack on the rear side. Use a cable with 3.5 mm pins at both ends, one end connected to the aux-in jack on the radio, the
other end connected to the earphone jack on the audio device (or line out socket if available).
Press [Mode] until “AUX IN” shows on the display. Play music on the connected device, the sound will be emitted from the
radio.
Alarms will only sound when the unit is “ON” (mains or battery power) or in “STANDBY” (mains power only).
Alarms can be switched on or off in standby mode, however, the alarm parameters can only be set when the unit is turned on.
To set or change alarm 1, press [Alarm] once, then select “ON” and press [Tune/Select]. To set or change alarm 2, press
[Alarm] twice, then select “ON” and press [Tune/Select]. To exit the alarm setting mode, press [Alarm] again.
The alarm setup prompts you for the following parameters. Select a value for each parameter by turning the [Tune/Select]
knob and press [Tune/Select] to confirm and prompt the next parameter.
• Hours
• Minutes
• Daily, Weekdays, Weekends, Once
Choose the days on which the alarm is active.
• Source – Beeper 1, Beeper 2, DAB or FM
Press [Alarm] or [Power] when the alarm is sounding to shut it off. The alarm will reset for the next day. The alarm will
automatically shut off after 59 minutes when no input is registered.
