165837
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
ENGLISH
connect its turn-on control to REMOTE OUT output (Fig. 2). A green LED ON indicates when
unit is turned on (Fig. 1).
MUTING CONTROL
VR series amplifiers are provided with automatic muting, delayed at turn-on, and rapid at turn-
off. Turn-on delay time can be externally regulated: MUTE DELAY (Fig. 3). This adjustment allows
the VR's entry into function to be acoustically synchronized with that of a second amplifier whose
muting delay cannot be adjusted. With the VR series, two muting connections are provided.
(Faston 2.8 mm): MUTE IN and MUTE OUT (Fig. 2). By connecting a control to MUTE IN the
amplifier will remain on hold. This input can be connected to radio-cassette player if provided
with the appropriate output, or to the incoming call output of a car phone. When there is a phone
call the system is silenced. When the conversation is finished the sound comes back. If a second
amplifier is used MUTE OUT is connected to its MUTE IN and it then becomes dependant on
the VR for all muting functions. A chain connection is possible using VR amplifiers and the MUTE
DELAY adjustment is only done on the first one. (Fig. 4).
REGULATION
All controls are located on top of the device. (Fig. 3).
MUTE DELAY: see muting control.
MONO-STEREO: see mono connection.
SENSITIVITY: sensitivity adjustment LEVEL L-R separate for each channel.
BI-LEVEL: Allows choosing adequate sensitiviy level for radio-cassette player.
PROCEED AS FOLLOWS
1) Set BI-LEVEL push switch at 0.35-2.2V sensitivity.
2) Turn LEVEL L-R toward minimum sensitivity (-).
3) Turn radio-cassette player's volume to about 3/4 maximum volume.
4) Turn LEVEL L-R toward maximum sensitivity (+) until you get sporadic lighting of PEAK L-
R LEDS (Fig. 1) with high dynamic musical passages. If the LEDS don't light up even after
turning LEVEL L-R all the way up, repeat operation from the beginning setting the BI-LEVEL
at 0.08-0.5V.
IMPORTANT: IF YOU SHOULD HEAR DISTORTION PHENOMENA WITHOUT THE PEAK L-R
LIGHTING UP IT MEANS A DISTORTED SIGNAL IS COMING FROM THE RADIO-CASSETTE
PLAYER. TURN RADIO-CASSETTE PLAYER VOLUME DOWN UNTIL THERE'S NO LONGER ANY
DISTORTION. REPEAT SETTING OPERATION OMITTING STEP 3.
PROTECTION
1) Output protection. Any type of short circuit in the speaker wires, be it between themselves
or to ground, will cause no damage.
2) Temperature protection. Anomolous operating conditions or high ambience temperature
(above 60°C - 140°F) cannot cause dangerous overheating.
3) Protection against inverted polarity. If the polarity of the power supply cables should be
mistakenly inverted the fuse will blow and electronic circuitry be protected. The fuse must
be replaced with an identical one.
4) Protection against continuous output current.
5) Protection against excessive loads dangerous to internal circuitry.
A red LED (SAFE) indicates intervention of protection circuits. Once the cause of malfunction
is eliminated you need only turn off radio-cassette player and turn it back on. The amplifier will
return to normal function.
CHARACTERISTICS
, has concentrated all of its know-how on the VR series of amplifiers rendering them
as technologically advanced as can be made available today. Every aspect has been extensively
attended to and resolved in the best possible way, not only through innovative solutions, but
also by using high quality componentry, paying meticulous attention to detail, and providing
accessory functions to maximize practicality. The PMW regulated type power supply uses
MOSFET transistors which allow a remarkable power capability which doesn't diminish when
battery voltage drops. A second separate voltage, stabilized and appropriately filtered, feeds the
preamplification stages allowing an elevated overall rendering for better heat dissipation
capabilities and to eliminate the classic disturbances generated by the power supply. The
specularly separated PRE stages and a special lay-out permit high disturbance rejection and
a considerable improvement in common mode rejection. The final stage's input employs a
complementary pair of constant current differential transistors polarized by LEDs with clearly
advantageous results in terms of stability and tonal neutratity. The CASCODE voltage driver is
appropriately treated in order to take complete advantage of the superior dynamics of this
configuration. The power stage is made up of a PURE COMPLEMENTARY SYMETRIC TRIPLET
for maximum current linearization, and final stage transistors able to handle currents considerably
higher than those normally required. Total feedback level under 10 dB, the adoption of some
local feedback, and a DC SERVO circuit allow for elimination of crossover distortion at low power
and the right balance of THD and TIM distortion at high power. So ample driving possibilities
are assured which can handle even the most difficult loads. In fact, the undistorted output power
follows a nearly linear path up to loads of one Ohm. Because of these features your VR amplifier
can only provide you with the very finest in listening enjoyment. At we thank you
for rewarding our work which is always aimed at reaching the very best results.
PRECAUTIONS
1) In order for this device to function properly it's important that it be installed in a spot where
the temperature doesn't fall below 0°C (32° F) or rise above 55°C (131° F).
2) It must be installed in a dry and well ventilated spot.
3) The power supply voltage is 12Vcc negative to ground. Make sure that the characteristics
of the vehicle's electrical system are compatible.
4) For safe driving it's advised to listen to music at a volume level that won't drown out external
traffic noise.
INSTALLATION
The VR series is characterized by its relatively compact size considering the features it offers.
This makes installation possible in even the most unlikely places. For mounting use 4 self-
threading screws and protection plastic rings provided (Fig. 3).IMPORTANT: The wooden
moulding which protects controls on top of device must be removed before installing. This
is done by loosening the two bolts with 5mm allen key provided. Once the installation is
completed and proper settings have been made the protective moulding is replaced. For
optimum results it's advised to use products to complete your installation.
These include: power cables, signal cables, speaker wires, RCA connectors and all
accessories needed to complete the wiring.
INPUT CONNECTIONS
PIN RCA CONNECTORS (IN L-R) Fig. 1. Observing polarity, connect L-R inputs to respective
preamplified outputs on radio-cassette player or electronic crossover if used. If the radio-
cassette player's output GND isn't connected to car body, the braided shield of shielded cable
must be connected to the radio-cassette player's chassis.
OUTPUT CONNECTIONS
THREADED CONNECTORS (SPEAKER L-R) Fig. 1. Connect to speakers or speaker system's
passive crossover observing polarity.
IMPORTANT: Never connect the outputs to ground or to each other. If a crossover filter is
used be sure the two channels don't have a common ground.
MONO CONNECTION
Use IN R input (Fig. 1). Draw output from +L, -R (SPEAKERS L-R7) Fig. 1. Position MONO/
STEREO push switch (Fig. 3) to MONO. It's possible to use MONO just for SUBWOOFER
frequencies and STEREO for the higher frequencies. Leave the MONO/STEREO button in STEREO
position and connect according to schematic shown in Fig. 5. Refer to chart for inductance and
capacity values relative to desired crossover frequency.
POWER SUPPLY CONNECTION
Threaded connectors (POWER) Fig. 2. + POWER is connected directly to positive car battery
with fuse and fuseholder (provided) interposed in it's proximity. - POWER is connected to the
car body (Ground) taking care to assure excellent electrical contact; see fig. 6. IMPORTANT:
Use wires of adeguate diameter (minimun 6 mm or 3 A.W.G.).
TURN ON CONTROL CONNECTION
2.8mm Faston connector (REMOTE) Fig. 2. Connect REMOTE IN input to radio-cassette player's
REMOTE, AUX output, if provided, or electric antenna output. If a second amplifier is used,
SPECIFICATIONS VR 203 VR 206 VR209
Power supply 11-15 VDC 11-15 VDC 11-15 VDC
Idle current 1.0A 1.2A 1.4A
Max consumption cont. (4 Ohm) 15A 20A 30A
Distorsion-THD (1KHz-90% Out) 0.06% 0.06% 0.06%
Cont. out power (2x4 Ohm- 13 Volt) 40W 7 0W 110W
Cont. out power (2x2 Ohm- 13 Volt) 70W 130W 200W
Impulsive power (1 Ohm - 13 Volt) 100W 190W 300W
Mono out power (4 Ohm - 13 Volt) 140W 250W 400W
Band width (-3dB) 3 Hz-75KHz 3Hz-75KHz 3Hz-75KHz
Dumping factor 110 115 120
Rise time 4 µS4µS4 µS
Signal to noise ratio (A) 105 dB 105 dB 105 dB
REMOTE IN 3-16 VDC 3-16 VDC 3-16 VDC
REMOTE OUT 3-16 VDC 3-16 VDC 3-16 VDC
MUTE IN 3-16 VDC 3-16 VDC 3-16 VDC
MUTE OUT 12 VDC 12 VDC 12 VDC
Input sensitivity (hi) RMS 0.08-0.5V 0.08-0.5V 0.08-0.5V
Input sensitivity (lo) RMS 0.35-2.2V 0.35-2.2V 0.35-2.2V
Out impedance 2-4-8 Ohm 2-4-8 Ohm 2-4-8 Ohm
Input impedance 15 KOhm 15 KOhm 15 KOhm
Size WxHxD (mm) 256x57x230 256x57x260 256x57x290
Size WxHxD (Inches) 10.07x2.24x9.05 10.07x2.24x10.23 10.07x2.24x11.41
Weight (Kg) 3.300 3.700 4.100
Weight (lbs) 7.27 8.15 9.03
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Audison vr 203 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Audison vr 203 in de taal/talen: Engels, Italiaans als bijlage per email.

De handleiding is 2,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info