583752
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
128-6992
6 of 8
6
"Programming System Features" shown later in this installation guide to learn the operation of the valet/program/manual
override switch.
POWER DOOR LOCK HARNESS
3PIN White Plug w/3 Wires; Green, Blue & Blue/Red
The connection of the power door lock/unlock wires has already been explained. Route the three pin connector to the unit
and plug the connector into the mating white three pin connector shell of the control module. Do not force the connector,
it will only plug in one way.
PROGRAMMING FEATURES:
There are seven (7) Programmable Features on this system. Study the list below, keeping in mind the features and their
defaults, (how it comes programmed from the factory), and decide how best to program the UNIT for your particular
installation.
Programmable Features:
Features 1 Chirp 2 Chirp 3 Chirps Default
First Passive Arming Active Arming Active Arming
Second Ignition D/L ON Ignition D/L OFF Ignition D/L OFF
Third Ignition D/UL ON Ignition D/UL OFF Ignition D/UL OFF
Fourth Chirps ON Chirps OFF Chirps ON
Fifth Passive D/L Active D/L Active D/L
Sixth Siren Output Horn Output Horn Output
Seventh 800ms D/L Pulse 3.5 Sec. D/L Pulse 800ms D/L Pulse 800ms Door Lock
Double 800ms D/UL Pulses
To Program These Features:
Entering the Programming Mode involves operating the Ignition Switch and the Valet/Program/Manual Override Switch in
a particular sequence. This sequence is very time dependent, in other words it must be performed
quickly in order for you
to enter the mode. This sequence is also only one step different from the Transmitter Programming Mode, so make
certain you perform the sequence properly.
Upon entering the Programming Mode, the system is immediately set to allow adjustment of the First Programmable
Feature. That First feature, "Passive or Active Arming", can then be set ON or OFF by pressing the lock button of the
transmitter. The system confirms that it is set to adjust the First feature by repeatedly flashing the LED once, with a pause
in between each flash. The system will then report how the feature has been set by the number of chirps heard after
pressing the transmitter button. Toggling the Valet/Program/Manual Override Switch once again will advance you to the
Second Programmable Feature, confirmed by a repeating two LED flashes, with a pause in between each flash, etc.
It is important to note that when you first enter the Programming Mode, you are automatically positioned to adjust the First
Programmable Feature and that the Valet/Program/Manual Override Switch allows you to toggle from there through each
of the six more programmable features. However, it will not allow you to return to any feature once you have toggled past
it. Should you accidentally toggle past the feature you wanted to program, you must exit and re-enter the Programming
Mode and then adjust the feature you missed.
It is also important to note that you may toggle past as many programmable features as you wish without having to adjust
them. Each time you toggle forward to a new feature, the horn will chirp the appropriate number of times (1, 2, or 3 times)
to indicate how that feature is currently set, and the LED will flash the appropriate number of times to indicate the number
of the feature (First through Seventh) that you are set to adjust. For example, you might enter the mode and toggle the
Valet/Program/Manual Override Switch 3 times in order to adjust the Fourth programmable feature. The system would
respond with 1 Chirp, and the LED would begin to flash 4 Flashes, pause, and repeat. This has told you that the system
is ready for you to adjust the Fourth programmable feature, and that it is currently programmed for Chirps ON. A single
press of the lock button of the transmitter will cause the system to produce 2 Chirps. This signifies that you have
changed the programming to Chirps OFF. Please follow the programming procedure on the next page, and refer to the
list of the Programmable Features above when programming the system.
To program these selectable features;
Action System Response LED Response
Turn ignition on No response
Turn the valet switch on then off 3 times 1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off Short chirp, then long chirp
First Then On 2 chirps = active arming 1 Flash pause
Press transmitter Lock button to change 1 chirp = passive arming
or
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Audiovox AX-45 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Audiovox AX-45 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info