583950
7
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
128-8604
7 of 8
2. Shut off the vehicle using the keychain transmitter by pressing and releasing
the remote start transmitter button a second two times in succession.
3. Within 10 seconds of step 2, activate the RF start command two times. In other
words, press and release the transmitter button 4 times in succession.
The parking lights will flash 4 times indicating the timed start mode is activated.
CANCELING THE AUTOMATIC START UP TIMER
To cancel the automatic start up timer do one of the following;
1. Start the vehicle manually with the use of the ignition key and depress the brake pedal.
2. Remote start the vehicle using your keychain RF transmitter.
And then shut off the vehicle using the keychain RF transmitter.
On Glass Mounted Push-Button SAFETY CONTROL SWITCH
The Push-Button LED safety control switch allows you to temporarily disable the remote
starting function of the system. This recommended whenever the vehicle is being serviced. To
place the system in the service mode:
1. With the system disarmed/unlocked, and the ignition switch off Press and Hold the push-
button switch found on the glass mounted receiver assembly.
2. Turn the ignition switch on, off, on, off, on, off.
3. The LED begins to flash two short flashes followed by one long flashes and continues
this pattern until returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start is in the service
mode and will not start from RF or any other input Posse or otherwise.
To Exit R/S Override Mode
1. With the system disarmed, Press and Hold the push-button switch on.
2. Turn the ignition switch on, off, on, off, on, off.
3. The LED turns off indicating that the R/S unit is fully functional one again.
BATTERY REPLACEMENT
Your one button transmitter includes a battery #GP27a that will need to be
replaced from time to time. If you notice diminished range, or if the LED on
the transmitter lights dimly, the battery should be replaced. To do so:
1. Remove the 0 point philips head screw found at the lower portion in the rear of the case.
2. Carefully separate the two transmitter case halves.
3. Remove the battery noting the proper orientation/polarity of the battery. Properly dispose of
the discharged battery.
4. Install the new battery being certain to correctly arrange the proper polarity.
5. Carefully close the case halves, finish by re-install the screw removed in step 1.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Audiovox AS9233ST bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Audiovox AS9233ST in de taal/talen: Engels als bijlage per email.

De handleiding is 0,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info