625602
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
GAIN
GAIN
CHANNEL 3 CHANNEL 4
IN
OUT
IN
OUT
GAIN
CHANNEL 1 CHANNEL 2
IN
OUT
GAIN
IN
OUT
NORMAL
BRIDGED
CHANNEL 1 & 2 BRIDGED CHANNEL 3 & 4 BRIDGED
220-240v~
100-120v~
CH3&4
CH1
CH3
CH4CH2
CH1&2
SERIAL No.
~50/60Hz
350W
e
f
g
h
GAIN
GAIN
CHANNEL 3 CHANNEL 4
IN
OUT
IN
OUT
GAIN
CHANNEL 1 CHANNEL 2
IN
OUT
GAIN
IN
OUT
NORMAL
BRIDGED
CHANNEL 1 & 2 BRIDGED CHANNEL 3 & 4 BRIDGED
220-240v~
100-120v~
CH3&4
CH1
CH3
CH4CH2
CH1&2
SERIAL No.
~50/60Hz
350W
a
b
c
d
Fault conditions:
Under fault conditions such as short circuit, over-current (load impedance too low) and over temperature the level meter for the
affected channels will show no signal (white lights extinguished) and the red "0dB" LED will light indicating protection is
operating. All protection systems are auto-recovering (no latching of faults) so that normal operation resumes as soon as the
fault condition is removed.
Please note that the protection systems are shared in pairs, channels 1 & 2 are paired and channels 3 & 4 are paired. Hence
under a fault condition on channel 1, for example, both channels 1 & 2 will be shut down until the fault is cleared. Likewise, a
fault on channel 4 would result in channels 3 & 4 shutting down etc.
Limiter operation:
The amplifier has a separate limiter for each channel and this has been carefully balanced to provide protection against clipping
whilst still allowing the full output potential to be realised with music signals. Under conditions which would normally cause the
output to clip the limiter will automatically reduce the gain to prevent audible distortion. Some momentary clipping of music
transients will occur but this is generally inaudible and allows the perceived loudness to be greater than if all clipping were
strictly eliminated.
The limiter provides valuable protection for both the loudspeakers and the listener’s ears under overdrive conditions.
To bridge channels 1 & 2:
Note: only the channel 1 level meter will operate.
Channels 1 and 2 operate as independent channels with a 4 Ohm minimum load capability. In the "bridged" position channels 1
and 2 operate as a single high output channel with an 8 Ohm minimum load capability. See wiring diagram for connection
details.
To bridge channels 3 & 4:
Note: Only the channel 3 level meter will operate.
a - Apply the input signal to channel 1 only.
Leave channel 2 input disconnected.
b - Connect the loudspeaker/s to the two
terminals as marked on the rear panel
(positive at very top and negative at very
bottom).
c - Set the mode switch for channels 1 & 2 to
bridged position.
d - Gain is adjusted with the channel 1 gain
control only (channel 2 gain control has no
effect)
e -Apply the input signal to channel 3 only. Leave
channel 4 input disconnected.
f - Connect the loudspeaker/s to the two
terminals as marked on the rear panel (positive
at very top and negative at very bottom).
g - Set the mode switch for channels 3 & 4 to
bridged position.
h - Gain is adjusted with the channel 3 gain
control only (channel 4 gain control has no
effect)
Bridge Mode
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Audica Microplus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Audica Microplus in de taal/talen: Engels als bijlage per email.

De handleiding is 1,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info