824009
3
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
3
3
3
Installing an appliance at altitude increases th
e air outlet temperature (
by
approximately 10°C per 1,000 m of elevation).
Installing vertical appliances above an altitude of 1,000 m is not recommended (
risk of faulty
operation). Installing a vertical appliance horizontally, and vice versa, is prohibited. Using the
appliance in a mobile configuration, on feet or on rollers, is prohibited.
Your appliance's references
These are located on the left-hand side of the appliance.
The commercial Code and the serial Number will inform the manufacturer of the type of appliance
that you have acquired. Enter the commercial code and the serial number in the warranty section at
the back of this manual.
A Standards, quality labels
B Brand name
C Commercial code
D Manufacturer's reference
E Serial No.
F Manufacturer's No.
28
periods. You are notified of these periods
through the transmission of a private radio
message, depending on the system that is
installed. This function is available as of the
deployment of the EDF LINKY® system and
requires the installation of Cozytouch.
Indicator light
luminosity
Allows the luminosity level of the ring (
on
indicator
) to be adjusted
.
Restrictions
Max.
temperature
Allows a maximum setpoint temperature to
be recorded that must not be exceeded. It is
set to 2C by default and can be changed
(
from 1C to 28°C
).
Access
control
Allows the appliance's settings to be partially
or fully locked.
PIN code
Allows a personal access code to be
recorded in the Expert Menu. Once
activated, access to the Expert Menu is
encoded.
Your personal code can be noted here.
To deactivate the code, return to the Expert
Menu, enter your personal code, and return
to Configurations => Restrictions => PIN
Code.
Connectivities
Send the
security key The security key secures your installation
to prevent interference with nearby
equipment.
Key exchange provides the possibility of
connecting an control point to your
installation.
Allows the security key to be sent to an
control point.
Use this operation if the appliances
are paired.
Receive
the
security key
Allows the security key to be received from
an control point.
Makes existing pairing inoperative if the
security key is not transmitted to the other
pairs.
Authorise
connection
Following key exchange, this operation is
required to enable connection to an
energy management system that is not part
of
our brand.
Reset
Connectivities
Deletes all connectivities
(pairing of
appliances, connection to the app, connection to
a centralised control point).
Test
Heating
element
Starts
-
up the heating
element for 5 minutes to check
operation.
29
Presence
sensor
Activates the sensor to check correct operation
(not available
on the
low height
model).
Radio
Test signal
transmission
Checks that there is good radio
communication between two appliances by
transmitting a signal from one appliance and
receiving a signal on the other appliance. If
the signal is weak, then there is a risk of
losing communication. Check the installation
(distance and/or obstacles between the
appliances).
Test signal
reception
To exit the Expert
Menu:
Press
together for 5 seconds
or
Wait
2 minutes
Power cut-off
Our appliances are compatible with various power cut-off systems. However, you should not use
power cut-off by interrupting the supply circuit power supply since this
system is incompatible with our appliances. Sudden unintentional and
repeated interruptions to the electrical power supply can cause wear
and damage to the electronic boards that will not be covered by the
manufacturer's warranty.
Irrespective of the selected Mode, during power cut-off periods, your
appliance will display "Priority power cut-off sequence".
Help
Problems encountered
Check to be
undertaken
The control unit screen does not
turn on.
Check that the switch located behind or on the side of the
appliance is set to the I position.
Check that the appliance is properly powered.
The
ring
around the "On /
Standby" button does not turn
on.
Check the luminosity adjustment level
(refer to the Expert
Menu Chapter).
The appliance does not heat up.
If you have accessed programming, check that the
programming is set to COMFORT.
Check that the installation's circuit-breakers are triggered
or even that the cut-off device (if present) has not cut-off
heating.
If the ambient air temperature in the room is higher than
the setpoint temperature, then it is normal for the appliance
not to heat up. Check that your appliance has not switched
to Frost Protection via the pilot wire.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Atlantic Galapagos - Vertical bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Atlantic Galapagos - Vertical in de taal/talen: Engels als bijlage per email.

De handleiding is 3,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info