702740
2
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
- 2 -
SPECIFICATIONS
Input voltage ........................................................................... 9.5 to 16 VDC
Current
Typical ..................................................................................... 15 mA
Maximum ................................................................................. 25 mA
Electrical configuration ....................................................................... Form C
Relay rating ....................................................................... 16 V, 50 mA max.
Tamper switch rating ....................................................... 12 V, 50 mA max.
Detection range ............................................................ 0.9 m - 7.6 m x 360°
Alarm response ................................................................................... 4 sec.
Minimum glass size ............................................................. 30.5 cm x 61 cm
Recommended glass thickness:
Plate ........................................................................ 2.5 mm - 6.5 mm
Tempered .................................................................. 3 mm 6.5 mm
Wired ...................................................................................... 6.5 mm
Laminated .............................................................................. 6.5 mm
Operating temperature ....................................................................0° - 50°C
Relative humidity .................................................. 10 - 90% non-condensing
Round housing dimensions: ............................................. 2 x 10 cm (D x Æ)
Rectangle housing dimensions: ....................... 11.5 x 7 x 2 cm (H x W x D)
Color ................................................................................................. White
Field wiring size ......................................................................... 18-24 AWG
SETTING THE R ANGE
The detector has a spring clip (J3) to set room size. See Figure 4. Use the
following table to determine what setting to use for an application.
Setting Description
Open Sets the range for 1.5 m to 7.6 m. Use for rooms
30 m² and larger. Default
Closed Sets the range 1 m to 3 m. Use for rooms smaller
than 30 m².
TESTING THE D ETECTOR
Use a Sentrol 5709C hand-held tester to verify detector range and operation.
To test the detector:
1. Set the tester to the appropriate glass-type setting. Use the tempered
setting if you are unsure about the glass type.
2. Put the detector in test mode as follows:
- Hold the tester close to the detector. See Figure 5.
- Activate the tester.
The LED on the detector lights for 4 seconds and then starts flashing to
indicate the detector is in test mode. The relay opens for 4 seconds, then
returns to standby.
3. Hold the tester near the surface of the glass to be protected and aim the
speaker at the detector. Be sure the tester is at the point on the glass
farthest from the detector. If closed curtains are present, hold the tester
behind them. See Figure 6.
4. Press the test button on the tester. The LED on the detector should stay
on for 4 seconds to indicate the glass is within detection range of the
detector. If the LED does not stay on for 4 seconds, move the detector
and retest.
UNDERSTANDING THE LED
The red LED located on the front of the detector indicates the status of the
unit as follows:
Status LED indication
Power on Flashes when power is applied.
Clap test/Alarm
memory In response to the clap test:
Flashes twice to indicate the detector has power
and is functioning properly.
Or
On for 4 seconds to indicate the detector has
alarmed.
Alarm On for 4 seconds with relay when breaking glass
is detected.
Test mode On for 4 seconds with relay, then flashes for 60
seconds. Each test trigger resets the test mode
clock and the LED restarts flashing for 60
seconds.
USING THE H AND-CLAP T EST AND A LARM M EMORY
Check the alarm memory and detector operation with the hand-clap test as
follows:
1. Standing under the detector, clap your hands together.
2. Observe the LED on the detector.
If the detector has power and is functioning properly, the LED quickly
flashes twice.
If the detector has alarmed, the LED will light for 4 seconds. Cycle the
power to clear the alarm memory.
The hand-clap test is intended as a functional test and is not an accurate
indication of detector range.
J3 Spring clip
Figure 4 - Detector Knockout Locations
Figure 5 Using the Tester
Figure 6 - Testing the Range
• Single
• Continuous
Plate •
Tempered •
Laminated •
Battery LED
Battery is OK if LED
stays on during test
5709C
Shatter Series Tester
Use for testing:
ShatterPro
Shatterbox
Shatterbox II
ShatterSwitch
SENTROL
2.5 cm
Knockouts
Knockouts
Slot
J3
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech SHATTERPRO 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech SHATTERPRO 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds als bijlage per email.

De handleiding is 0,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info