702735
2
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
EN: Installation instructions
Information
This is the GE Door-Window Sensor 868 Mhz Installation
Instructions for models RF300NW8, RF300NW8B, NX-850N-I and
NX-851N-I.
The Universal Transmitter is provided with a 3-volt DL 123A
Lithium Battery and an external magnet. It contains an internal
reed switch, connections for an external open or closed contact
loop and a cover and pry off tamper switch. Two jumpers allow
you to select internal or external reed, and normally open or
closed external loop.
This Universal Transmitter is a single address device and will
transmit Alarm, Tamper, Restore, and Low Battery codes. It also
transmits a "supervisory" signal every 15 minutes to the receiver
indicating its status and presence.
Explanation of figures
1 Opening the transmitter housing
A Cover
B Slot
2 Securing the transmitter housing
3 Universal transmitter layout
C Mounting hole
D Magnet
E Aligning mark
F Battery holder
G Reed contact
H External contact input
I J2, external contact
J J3, reed contact
K Mounting hole
Jumpers
J2 - External contact (fig. 3, I) J3 - Reed contact (fig. 3, J)
Normally open (default)
Reed enabled (default)
Normally closed Reed disabled
Note: You should only use the internal reed OR the external
contact.
Installation
Recommended mounting surfaces include plastic, wooden and
aluminium door/window frames. Mounting on steel surfaces must
be avoided.
The maximum gap between the case of the transmitter and the
external magnet cannot be greater than 10 mm. For applications
requiring a gap of 10 mm or greater, use an external contact
switch connected to the external loop circuit and disable the
internal reed switch.
The Universal Transmitter should be tested at the intended
location before permanently mounting to make sure that proper
signal transmissions can be made. Consult the appropriate Control
Panel Instructions for programming and test details.
Opening, closing and mounting
To remove the sensor cover (fig. 1, A), press a small screwdriver
into the slot (fig. 1, B) at the end of the sensor while lifting the
cover. Make sure the unit and magnet can be aligned properly in
the intended mounting position and the cover can be
opened/closed after mounting. Mount the unit with the two flat
head screws (included) using the slotted mounting hole in the base
(fig. 3, K) and the mounting hole next to the tamper switch
(fig. 3, C).
Replace the cover by hooking in the "lower end" first and then
snapping the opposite cover end into place. Secure it (fig. 2) with a
self-taping screw (included).
EN-compliant installation
In order to install your wireless product according to EN50131-1,
please screw the transmitter housing according to fig. 2.
Use of the internal reed (supplied)
It is important that the magnet (fig. 3, D) is installed in such a way
that it is aligned with the mark (fig. 3, E) on the detector. Verify that
the reed switch (fig. 3, G) is enabled, and jumpers J2 (fig. 3, I) and
J3 (fig. 3, J) are in the standard position.
Use of an external contact loop
The transmitter can monitor "open circuit" or "closed circuit"
contacts but not both at the same time. Select and set Jumper
J2 (fig. 3, I) for "Normally Open" or "Normally Closed" loop. An
alarm will be transmitted when the contact opens (J2 in "Normally
Closed" position) or when the contact is closed (J2 in "Normally
Open" position). When the loop contact restores, a restore event
will be transmitted. Connect the external loop contact to the two
way screw terminal block (fig. 3, H). Jumper J2 should be set to the
"Normally Open" position (default position) if the external loop is
not used. Jumper J3 should be set to "reed disabled".
Note: In EN/INCERT approved intrusion security applications the
usage of the external input is prohibited.
Use of pry-off tamper
To allow the functioning of the pry-off tamper, you need to fit a
screw in the mounting hole (fig. 3, C). If the sensor is removed from
the wall the plastic part at the back of the base and a part of the
PCB breaks out.
Battery installation and removal
Insert the battery into the battery holder (fig. 3, F), observing
correct polarity.
Caution: Batteries can explode or cause burns if disassembled,
recharged or exposed to fire or high temperature. Please dispose
of old batteries properly.
Upon indication of low battery, please remove the battery from its
holder. Dispose the used battery according to the enclosed
WEEE instructions and/or local government authorities.
2 of 8 P/N KEM-PK27107D • REV 00.02 • ISS 24NOV08
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech RF300NW8 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech RF300NW8 in de taal/talen: Engels, Italiaans als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info