702288
1
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
© 2003 GE Interlogix B.V. 1047430
All Rights Reserved 12/2003
1
2
3
4
5
6
7
8
9
10
NC OC
Gouvars, Frederique (IndSys, GE Interlogix)
GSM Module
WHAT DOES IT DO?
The ATS7300 enables alarm reporting via GSM. All reporting
formats available through PSTN are fully functional, including voice
reporting or audio listen-in.The GSM module can be used for
primary reporting as well as back-up reporting (using multiple
central stations).
The ATS7300 has a provision to establish a reliable connection for
remote up-/downloading to and from the ATS panel. In data mode
the GSM module even can establish a connection up to 4800 baud
(for more details and programming options see ATS2000 / 3000 /
4000 Programming manual). A general fault indicator is available
(OC) to indicate if the battery is present, the battery fuse is ok and
the GSM network is detected.
IMPORTANT:
Disable PIN code request on your SIM card (via
any mobile telephone)
For proper operation a GSM card with subscription
is mandatory (NOT pre-paid).
The ATS7300 will only operate (dial/answer) when
connected to the home network.
A GSM module during operation can require a
maximum of 2A peak current; the back-up battery
normally wired to the control panel is now also
wired to the GSM module. The GSM module
checks the battery operation and disconnects the
battery when the battery voltage drops below 9
volts to preserve the battery (deep discharge
protection)
Make sure the antenna itself is placed outside the
control panel.
To do up/download via the GSM module, use a SIM
card that has fax and data enabled.
MOUNTING LOCATION
The ATS7300 must be mounted inside an ATS panel housing.
Important:
1. Disconnect the mains power before opening the cabinet.
Disconnect AC mains plug from AC mains wall socket.
OR
Disconnect the mains with a dedicated circuit breaker.
2. Disconnect the battery (when applicable).
MOUNTING THE UNIT
Mounting the ATS7300 into the control panel (ATS4000, Ref.
to figure ).
1. Remove the screws and lift off the control panel PCB.
2. Place the extension pillars with the plastic rings on top of the
existing pillars .
3. Place the clips in the square holes .
4. Mount the ATS7300 using the screws and extension pillars .
5. Place the ATS control panel PCB back into its original position.
Mounting the ATS7300 into the control panel
(ATS2000/3000/4500, Ref. to figure )
1. Place the clips in the square holes (use metal pillars when
available).
2. Mount the ATS7300 using screws.
Connecting the GSM module
Disconnect AC mains plug from AC mains wall socket
1. Remove the battery wires that run from the battery to the
control panel.
2. Add the blue “tap connectors” to the red and blue (or black)
battery leads.
3. Connect the additional wires, which will be clamped to the
GSM module.
4. Before clamping ensure that the battery leads will reach the
GMS module as well as the battery.
5. Connect the red wire to BATT IN + and the battery.
6. Connect the blue (or black) wire to BATT IN – and the battery.
ATS7300
GSM Module
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech ATS7300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech ATS7300 in de taal/talen: Nederlands, Engels, Frans, Italiaans, Spaans, Pools, Deens, Noors als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info