702271
2
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
2
!
Arming Stations
MOUNTING THE UNIT
The RAS cover is hinged at the bottom. To open, grasp the cover at
the sides or the top and pull gently — the cover will swing down on
its pins. The cover may be fully removed by gently prising one of the
pins away from the body of the RAS and pulling. The metal mounting
plate at the rear is held by a locking screw. To remove the metal
mounting plate, loosen the screw by at least 8 mm (0.315 in), sliding
the mounting plate down, and then pulling the bottom of the mounting
plate away from the body of the RAS.
Attach the metal mounting plate to mounting surface using the three
screws provided. Ensure that the rear tamper button can rest on a
flat surface flush with the back of the mounting plate (avoid rough or
non-flat surfaces). If rear cable entry is used (through the mounting
plate), cut a hole in the mounting surface for cable access. Set the
RAS address using DIP switches 1 through 4 (see DIP Switch
settings below). Set the bus termination switch (DIP switch 5), if
required (see DIP Switch settings below). Terminate the bus cabling.
IMPORTANT:
All power should be turned off to the control panel
before wiring the RAS.
Insert plastic cable entry blanking plugs (provided) into the rear of the
RAS to blank any unused cable entry channels. Place the RAS onto
the mounting plate and lock in place by moving the unit down by
about 8 mm (0.315 in). Tighten the locking screw at the base of the
RAS till firm. Do not over-tighten.
LOCATION OF FEATURES ON REAR OF RAS (FIGURE )
1. Cable entry 4. Tamper switch
2. DIP switches 5. Locking screw
3. LAN terminals
CONNECTING CONTROL PANEL TO KEYPAD
Refer to the ATS control panel installation guide for instructions.
TAMPER SWITCH (FIGURE )
The rear tamper switch must be sealed for the system to work
correctly. Make sure that the tamper button is resting on a surface
such that it remains depressed when the RAS is mounted, and will
spring open when the RAS is tampered with. In operation, the LCD
display will show “RAS Tamper” when not sealed.
RAS DIP SWITCH SETTINGS (FIGURE )
A row of DIP switches is located on the rear of the RAS (figure )
and is used for setting the RAS address and the bus termination
(TERM) condition. These settings are described in the following
sections.
TERM Switch Use switch 5 to set TERM to ‘ON’, if needed.
There must be no more than two TERM switches or links set to ‘ON’
for any bus. Refer to the control panel installation guide for details
about the use of TERM switches or links.
RAS Address Set the RAS address using switches 1 to 4.
CONNECTIONS (FIGURE )
+ 13.8 VDC The RAS can be powered using the bus + and –
power from the control panel, if the distance between the RAS and
the control panel does not exceed 100 m (328 feet). Otherwise the
RAS can be powered by AUX PWR from a DGP, or by an auxiliary
power supply.
D+/D- D+ is the data positive connection and D- is the
data negative connection of the data bus.
The RAS is connected to the ATS panel via the RS485 data bus, up
to 1.5 km from the control panel or the four-door controller DGP. It is
recommended to use 2-pair twisted, shielded data cable
(WCAT52/54). The shield of any bus cable must be connected to
system ground at one end only. The ATS111x RAS is not provided
with an Earth connection for this purpose. If the bus is ‘daisy-chained’
to the RAS, ensure that the shield of the cable is jointed to provide
continuity of data cable shield.
RTE An RTE button (normally open, momentary
push-button switch) can be connected across the IN and 0V
terminals (see figure
). When pressed, the button controls the
request to exit function to
the panel.
IN A request to exit button (normally open, momentary push-
button switch) can be connected across “IN” and “-”. When pressed,
this button controls the request to exit function.
OUT Open collector output. Use the first output number of the
output controller assigned to the RAS. Refer to the ATS control panel
programming manual for details.
STATUS LED INDICATIONS (FIGURE )
A
Green The Power LED is on when the control
panel is powered by the AC supply.
!!
Yellow The Fault LED illuminates to indicate
detection of a system fault.
Blue The Access LED flashes when access to an
area assigned to the RAS is granted.
Red The Alarm LED illuminates when there is a
system tamper or an area assigned to the RAS is in
alarm state. The area may be identified by viewing the
16 area LEDs visible when the RAS cover
is open or removed.
AREA LED INDICATIONS (FIGURE )
When the RAS cover is open or removed, 16 red LEDs are visible
at the bottom of the RAS. Each LED represents an area, and the
indications are as follows:
The LED illuminates when its corresponding area is armed.
The LED flashes slowly when a fault is detected.
The LED flashes quickly when an alarm occurs.
OPERATING FEATURES
Keyboard Backlight and Night Light
The default keyboard backlight and night light settings are as follows:
Keyboard backlight on (bright) for approximately 4¼
minutes following a key press.
Night light on (dim).
These functions can be changed from the RAS menu.
LCD Contrast
The LCD contrast may be adjusted by pressing and holding the
*“MENU key while momentarily pressing the Ç or È keys to
change the display contrast. The default setting is 12.
LCD Backlight
The LCD backlight illuminates for 30 seconds following a key press.
Buzzer Tone
The Buzzer tone may be adjusted by pressing and holding the
“CLEAR” key while momentarily pressing the Ç or È keys to change
the buzzer tone. The default setting is 16.
LCD Text Format
The ATS1111/ATS1116 RAS has a 4 line x 16 character LCD and
may display text in three alternative formats, as follows:
Format 1 (default) wraps text using hyphens when a word is
broken onto the next line.
Format 2 wraps text without hyphens when a word is broken
onto the next line.
Format 3 wraps text to the next line without breaking words.
To change formats, press and hold the ‘0’ (zero) key while
momentarily pressing the Ç or È keys.
This option is not available on the ATS1110 or ATS1115 RASs with
2 line x 16 character LCD.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech ATS1110 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech ATS1110 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info