702269
2
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
2
EN
Installation Instructions
INTRODUCTION
The AD111 is an internal interface for an addressable
detector system. It connects a generic detector with dry
alarm and tamper contacts to the Advisor MASTER
ATS1290 Point-ID DGP. The interface is equipped with two
inputs for connecting the alarm relay and the tamper switch
of the detector, and an open collector output. This output
can be used for example; to enable/disable the alarm LED
on the detector (depending on the detector’s other
functionalities, which can be programmed).
DEVICE CATEGORY
The AD111 is of the device category I/O, type 2 and will be
automatically recognised after learning the device into the
ATS1290 DGP. For more details about device categories
and types, please refer to the ATS1290 manual.
MOUNTING THE UNIT
The AD111 PCB (Fig. ) is mounted underneath the PCB
in the housing of the detector that is connected to the
Point-ID bus (Fig. o). Connect terminals 1 to 4 to the Point
ID bus and external power supply.
CAUTION! Before mounting the AD111 Internal
PID interface in a (existing) PIR detector,
disconnect the mains power before opening the
panel, DGP or external power supply cabinet.
1. Open the detector.
2. Remove the PCB from the detector.
3. Connect the flying leads 5 - 11 to the existing detector
connections (see fig.
, and q).
Number Colour AD111 PIR
5 Black 0V from AD111 0V to PIR
6 Red +12V from AD111 +12V to PIR
7 Blue Alarm input Alarm output
8 Blue Alarm input Alarm output
9 Yellow Tamper input Tamper output
10 Yellow Tamper input Tamper output
11 White Walk test output Walk test input
4. Connect the Point ID bus and auxiliary power supply to
terminals 1 - 4 (see Fig. q.)
Important:
The Point ID bus in – (ground) must be coupled to the
external power supply in – (ground) to ensure correct
operation! Connect the bus and detector grounds in the
control panel or close to the detector where the auxiliary
power supply is located.
TOPOLOGY AND DETECTORS
Please refer to the ATS1290 manual.
CABLE SPECIFICATION
Please refer to the ATS1290 manual.
ADDRESS SETTING AND ZONE NUMBERING
Set the AD111 Internal PID Interface to its unique address
on the Point ID bus. For details, see figure
.
The address setting of the AD111 will immediately
correspond with zone number and output in the range of
the ATS1290 DGP
Refer also to the ATS1290 manual for the direct link to the
zone number (control panel).
For convenience the output also can be configured to
connect to any output in the DGP range (for more details
see the explanation at the end of the memory location
map).
THE ATS OUTPUT
The walk test can be programmed through the control
panel by activating an output in the DGP range.
MEMORY LOCATION MAP
Every PID device has its own characteristics concerning
related I/O lines or certain functionality of the device.
A total of 16 memory locations are reserved to configure
the PID devices. Only the first nine normally are user
configurable. This depends on the functionality of the
particular device.
For the AD111 internal PID interface only memory location
6 matters.
On memory location 6 the ATS-style output can be
configured.
*ATS-style output
The output can be used to enable/disable the Alarm LED or
Walk Test LED on the detector. ATS output and zone
numbering are equivalent.
The default output number of the device equals the input
number when memory location 6 is set to 0 (default).
Please refer to the PID DGP manual for PID address
settings and zone numbering.
The output number on the AD111 can also be changed
within the DGP output range (e.g. DGP 1 output 17-32). If
the output of this device or all the outputs of similar devices
on the same DGP need to be programmed on for example
output 32, simply program memory location 6 of all those
I/O devices to 32.
TECHNICAL SPECIFICATIONS
Bus protocol ..................................... GE Interlogix Point ID
Bus voltage ..............................................12 V or 24 V
External power supply..............................9 V – 13.8 V
Current consumption from bus...................... 330 µA ±10%
Unit load for DGP..............................................................1
Address range........................................................0 to 255
Current O/C output...........................................100µA max.
Category.........................................................................I/O
Device type .....................................................................T2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech AD111 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech AD111 in de taal/talen: Nederlands, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info