702268
2
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
2
4. Drill the necessary holes for fixing the housing.
5. Fix the housing to the ceiling or wall.
6. Reinstall the PCB.
CONNECTING THE UNIT
Connect the AD011 to the detector and Point ID bus (see fig.
p)
1. Decide for a double or single resistor EOL configuration
2. Connect the detector alarm/tamper outputs via the
selected EOL resistor(s) to the input connectors 5 and 6.
3. Connect the external power supply to connectors 3 and
4.
4. Connect the alarm LED enable connection from the
detector to the open collector output 7 (if applicable).
5. Connect the Point ID bus to connectors 1 and 2.
Important:
The Point ID bus in – (ground) must be coupled to the external
power supply in – (ground) to ensure correct operation!
ADDRESS SETTING, ZONE NUMBERS AND OUTPUT
NUMBERS
Set the AD011 to its unique address on the Point ID bus. For
details, see figure
o.
The address setting of the AD011 will immediately
correspond with zone number and output in the range of the
ATS1290 DGP.
Refer also to the ATS1290 manual for the direct link to the
zone number (control panel).
For convenience the output also can be configured to
connect to any output in the DGP range (for more details see
the explanation at the and of the memory location map).
THE ATS OUTPUT
The walk test, for example, can be programmed through the
control panel by activating an output in the DGP range.
MEMORY LOCATION MAP
Every PID device has its own characteristics concerning
related I/O lines or certain functionality of the device.
A total of 16 memory locations are reserved to configure the
PID devices. Only the first nine normally are user
configurable. This depends on the functionality of the
particular device.
For the AD011 external PID interface only memory locations
3 and 6 matter.
On memory location 3 the zone type can be configured for
Single EOL, Double EOL (default) or the zone can be
switched off (the status will always be “Normal”).
The ATS-style output can be configured on memory location
6. For more details, please refer to the explanation at the end
of the Memory Location map.
MEMORY LOCATION MAP FOR AD011
Location Function Decimal values Binary values
3 Zone types*
0 = Zone is off
1 = Single EOL
2 = Double EOL (default)
0000 0000 = Zone is off
0000 0001 = Single EOL
0000 0010 = Double EOL (default)
6 ATS-style output**
0
0000 0000
ATS output number that controls the
AD011/AD111 output by means of “output on” /
“output off” *
*Zone Types
The ATS1290 default value for input type is Double EOL (2).
Consequently the normal state is a single EOL resistor, for
an alarm state it is two EOL resistors in series, and for an
input tamper it can be either "Short" or "Open".
**ATS-style output
The output can be used to enable/disable the Alarm LED or
Walk Test LED on the detector. ATS output and zone
numbering are equivalent.
The default output number of the device equals the input number
when memory location 6 is set to 0 (default).
Please refer to the PID DGP manual for PID address settings
and zone numbering.
The output number on the AD011 can also be changed within the
DGP output range (e.g. DGP 1 output 17-32).
If the output of this device or all the outputs of similar devices on the
same DGP need to be programmed on for example output 32,
simply program memory location 6 of all those I/O devices to 32.
TECHNICAL SPECIFICATIONS
Bus protocol ........................................ GE Interlogix Point ID
Bus voltage ........................................................12 or 24 V
External power supply....................................... 9 to 13.8 V
Current consumption from bus......................... 520 µA ±10%
Unit load for DGP.................................................................2
Address range........................................................... 0 to 255
Current O/C output.............................................100 µA max.
EOL resistors .........................................................2 x 4.7 k
Category ........................................................................... I/O
Device type ........................................................................T3
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech AD011 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech AD011 in de taal/talen: Nederlands, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info