454944
26
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
24
GB
model
CD 12 TX
dimensions
width cm 59,8
height cm 82
depth cm 53,7
capacity
1 - 5 Kg
electrical
connections
voltage 220/230 Volt 50 Hz
maximum absorbed power 2300 W
water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)
drum capacity 42 litres
spinning speed
up to 1150 rpm
This appliance conforms with the following E.E.C.
directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications
Using the Drilling Template
·
Place the top edge of the drilling template so that it is flush
with the top edge of the panel, making sure that it is positioned
correctly and centered in the horizontal direction (use the dotted
lines on the edges to line the template up). Mark the points on
the panel for the four holes.
· Use an appropriately sized router to mill the holes for the
two hinges, the rubber plug and the magnet.
Mounding the Parts onto the Wooden Panel
(Door)
· Insert the hinges into the holes (the movable part of the
hinge must be positioned facing away from the panel) and
fasten them with the 4 type A screws.
· Insert the magnet into the top hole on the opposite side
of the hinges and fasten it with the two type B screws.
· Insert the rubber plug into the bottom hole.
The panel is now ready to be mounted onto the machine.
Mounting the Panel into the machine
Insert the nib of the hinge (indicated by the arrow in fig. 9)
into the hole for the hinge and push the panel towards the
front of the machine. Fasten the two hinges with the type
D screws.
Inserting the machine into the Cabinet
· Push the machine into the opening, aligning it with the
cabinets (fig. 14).
· Regulate the adjustable feet to raise the machine to the
appropriate height.
· To adjust the position of the wooden panel in both the
vertical and horizontal directions, use the C and D screws,
as shown in fig. 15.
· If the machine is installed at the end of a set of modular
cabinets, mount either one or both of the guides for the
base molding (as shown in fig. 16) with the type F screws.
Adjust them for depth based on the position of the base
molding, and, if necessary, fasten the base to the guides.
Technical characteristics
90 mm
570
min
820
537
598
820 ÷ 870
600 min
D
C
C
Fig. 16
Fig. 14 Fig. 15
Control programs in compliance with IEC regulation 456:
Cotton program:
Turn knob A to the "program 2"setting;
Turn knob B to the "60°C" setting;
Press Extra economy button.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ariston CD 12 TX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ariston CD 12 TX in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 2,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ariston CD 12 TX

Ariston CD 12 TX Gebruiksaanwijzing - Nederlands - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info