642216
9
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
www.argonaudio.com 9
DA2 V2
Notice: If DA2V2 is connected with a Argon iNet6+ they have to be connected only by Optical digital out/in.
If iNet6+ is connected to DA2V2 via analogue RCA the volume function on the remote will not work properly
Power Management (Auto Stand-by)
According to the EC regulations implemented January 1
st
.
2013 Argon Audio DA2V2 will automatically go into auto
standby if it is without a music signal for 20 minutes.
This rule is applied by the EC in order to save power
consumption.
Basic Troubleshooting
If the LED does not light up, check...
that the AC power cord is firmly plugged into the rear panel
and wall outlet.
to make sure the amplifier rear panel power switch is ON.
that the amplifier is getting power from the wall outlet.
that the rear panel voltage match the operating voltage.
the fuse in the AC IN on the rear panel. If the fuse needs to
be replaced it is extremely important to replace only with
same fuse type and value.
If no sound output, check...
that the amplifier is turned on (blue LED illuminated)
to make sure the speakers are connected correctly
that the volume on the front panel is not all the way down.
the volume level on the iPod or other audio source.
If bass output is low, check...
speaker wire polarity (verify that wires are going to same
terminals on both speakers + to + and to -)
Using Optical cable… ensure that you have removed the
small plastic covers from the Optical cable connections
Specifications:
Type: Full class D, digital amplifier
Inputs: Digital USB2.0, 2 x Optical digital,
Analogue L/R RCA stereo input
Output: SUB-OUT, 1 set speaker output
Main voltage: 220-240V, 50/60Hz
Distortion: @4ohm 20-20Khz 0,3% @8ohm 20-20Khz 0,2%
Input sensitivity: 500mV (RCA) analogue
Frequency Response: (-1db @1Khz): 20Hz-20Khz
Output Power: 2X50W (RMS @4ohm)
Resolution: USB2.0 16bit/48Khz, Optical max.
16 bit/96Khz
Optical processing: Burr Brown 2704 processed via Sp/diff
and then D/A converted by AKM4388A
Notice: optical is not supported via Bluetooth to an Argon
BT2. Instead, use analogue input on DA2V2, if you intend to
connect an Argon Audio BT2 Bluetooth adaptor).
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Argon DA2 v2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Argon DA2 v2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info