665480
3
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
3
1. Remote control unit.
2. Remote control sensor: Detects the room temperature
around the remote control unit, the air conditioner is
controlled accordingly.
3. Air outlet: Conditioned air is blown out of the air
conditioner through the air outlet.
4.
Air intake: Air from the room is drawn into this section
and passes through air filter which removes dust.
5. Remote control receiver: This section picks up infrared
signals from the remote control unit (Transmitter).
6. Operation selector (without remote control): Push
the button to walk through the operation modes (OFF,
COOL and HEAT)
7. OPERATION lamp: This lamp lights up during
operation.
It blinks once to announce that the remote control
signal has been received and stored.
8. STANDBY lamp: This lamp lights up when the air
conditioner is connected to the power and ready to
receive the remote control command.
9. TIMER lamp: This lamp lights up when the system is
being controlled by the timer.
10. Air filter.
11. Condensate drain connection.
The OFF position does not disconnect the power. Use
the main power switch to turn off power completely.
WARNING
EG
NAME OF PARTS AND OPERATION SELECTOR SWITCH
5
6
7
8
9
3
10
11
2
1
4
NOTA
When the unit receives a signal from the remote
controller, all the three lamps (OPERATION, TIMER
and STANDBY) light up for a moment to indicate the
correct signal reception.
OFF LAMPS FUNTION
It is possible to set the air conditioner in order to let the
OPERATION, TIMER and STANDBY lamps always OFF,
even during operation.
Be sure that the remote controller is ON (using the ON/
OFF button) and that the symbol on the display of
remote controller is OFF, then Press contemporary the
IFEEL and FAN buttons on the remote control unit for more
then 5 seconds.
Repeat the same procedure to set again the normal
operation conditions.
If the air conditioner is powered, but the lamps are off, try
to activate them using this procedure.
In case of troubleshooting the air conditioner diagnostic
system activates the lamps accordingly, even if they are
set to OFF. See paragraph TROUBLESHOOTING for
further details.
The blinking of TIMER and STANDBY lamps and
OPERATION lamp ON, indicates that:
1. Indoor unit has not been addressed.
2. Heating mode has been selected, when the system
was in cooling mode, or vice versa.
Select the correct mode, compatible with the
system.
SEE AUTO-DIAGNOSIS TABLE
MULTI SPLIT SYSTEM
only
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Argo ADICS13DC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Argo ADICS13DC in de taal/talen: Engels als bijlage per email.

De handleiding is 1,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Argo ADICS13DC

Argo ADICS13DC Installatiehandleiding - Deutsch - 76 pagina's

Argo ADICS13DC Gebruiksaanwijzing - Deutsch - 15 pagina's

Argo ADICS13DC Installatiehandleiding - English, Français - 76 pagina's

Argo ADICS13DC Gebruiksaanwijzing - Français - 15 pagina's

Argo ADICS13DC Installatiehandleiding - Italiano, Português, Espanõl - 76 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info