578801
5
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
5
POSITIONING THE UNIT
Place your amplifier on a level, firm surface.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed
space such as a bookcase or cabinet as both of these will impede air
flow through the ventilation slots.
CONNECTING TO LOUDSPEAKERS
You can connect one or two pairs of loudspeakers to your amplifier,
provided each pair is rated between 816. If one or both pairs have
an impedance of less than 8, the combined load on the amplifier falls
below 4 and could cause an overload. If so, the overload protection
circuit engages and the amplifier will not work.
To connect one pair of loudspeakers, use the
SP1 terminals.
SP1 and SP2 terminals
4
Both sets of loudspeaker terminals can be switched off by pressing the
MUTE button on the remote control. To switch SP1 and SP2 independently,
use the front panel switch
7
(see page 7) or the remote control (see
page 10).
Your amplifier is fitted with loudspeaker terminals to BFA (British
Federation of Audio) standard specification.
BFA loudspeaker terminals
The terminal will accept spade terminals, bare wires or a BFA plug.
BFA plugs are available from your Arcam dealer. To connect a bare wire
or spade terminal, unscrew the red (or black) part of the loudspeaker
terminal first.
Insert the wire or spade terminal and screw it back up.
Installation: A32 integrated ampli er
Wiring your loudspeakers
LR
+–
PHONO
+–
SP1
SP2
POWER INLET
PRE OUTPWR IN
6 8 9 bk bl bm bn bo bp54 bq1
4 – 16 OHMS
L
R
L
R
L
R
VOLTAGE
SELECT
RECORD
OUT
PLAY
IN
TAPE/PROC
RECORD
OUT
PLAY
IN
VCR/TAPE 2 DVD AV TUNER CD AUX
INTEGRATED
PRE/PWR
MM
MC
32
REMOTE
IN
TRIG
OUT
7br
115/230V
Arcam A32 amplifier
R
L
+ +
Right
speaker
+
+
Left
speaker
CAUTION: Do not over tighten the loudspeaker terminals or use
a wrench, pliers, etc., as this could cause damage to the terminals
which will not be covered under warranty.
Connect the right speaker to the terminals on the back of your
amplifier marked
R and the left speaker to the terminals marked L.
Connect your loudspeakers so that the red (positive/+) terminal on
each loudspeaker is connected to the red (positive/+) terminal on the
amplifier. Your loudspeaker cables may be marked to show polarity
(negative/ and positive/+), if not, then the positive terminal can usually
be identified by a ridge or coloured marking.
Now connect your loudspeakers black (negative/) terminals to the
black (negative/) terminals on the amplifier.
Ensure that no stray strands of inner wires are allowed to touch
another cable or the amplifiers casing. This can cause a short circuit
and damage your amplifier!
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam FMJ P35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam FMJ P35 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info