578800
5
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
8
9
The use of high quality interconnect cables to and from your
integrated amplifier is recommended to ensure the best sound
quality (sonic performance).
The sockets carrying messages from your integrated amplifier are
marked L (left) and R (right), for identification. Sockets marked L
on your integrated amplifier should be connected to sockets
marked L on other equipment. All the line inputs (not PHONO)
have the same sensitivity and may be used with equipment other
than that labelled, if you need to do so.
bk
PROCESSOR/TAPE 1 RECORD OUT
Connect this output to the input sockets of your tape deck
(RECORD) or the tape or line input sockets of your AV processor.
bl
PROCESSOR/TAPE 1 PLAY IN
Connect this input to the output sockets of your tape deck
(PLAY) or the tape or line output sockets of your AV processor.
bm
VCR/TAPE 2 RECORD OUT
Connect this output to the input sockets of your tape deck
(RECORD).
bn
VCR/TAPE 2 PLAY IN
Connect this input to the output sockets of your tape deck
(PLAY).
bo
DVD
Connect this input to the audio outputs of a DVD player.
bp
AV
Connect this input to the audio outputs of an Audio-Visual
product such as a VCR, Laserdisc player or Nicam tuner.
bq
TUNER
Connect this input to the audio outputs of your radio tuner.
br
CD
Connect this input to the audio outputs of your CD player
or DAC (digital to analogue convertor).
bs
AUX
Connect this input to the audio outputs of any unit with a
line level output, eg. tape deck, tuner etc.
Please note:The AUX inputs MUST NOT be used if the
phono module is fitted.When the phono module is fitted
AUX becomes an output carrying the equalised phono
signal at line level.
PHONO OPTION - Please note:The phono inputs are on a
separate plug-in module which your Arcam dealer or
distributor can supply and fit.This module is compatible with
most high output moving coil and moving magnet cartridges
(MM) and low output moving coil cartridges (MC). MM or
MC is selected via an internal switch.Your cartridge type
should be specified when the module is fitted.
bt
MM
For connecting a turntable fitted with a high output moving
coil or a moving magnet (MM) cartridge.
ck
MC
For connecting a turntable fitted with a low output moving
coil (MC) cartridge.
cl
GROUND TERMINAL
For connecting your turntable earth lead (if fitted).
3
REMOTE CONNECTION
These connections are for use in multi-room installations. In
normal use there is no need to make any connections to
these sockets. If you are biamping with an Arcam power
amplifier see section ‘Remote Switching’ for details of how to
power both units on/off simultaneously.
8
GAIN
This switch allows you to change the sensitivity of the
amplifier to match the gain when biamping to external
power amp.The normal position is suitable for use when
biamping with Arcam power amplifiers.
The low gain position is suitable for certain specialist
home theatre systems. Before making any connections
ensure that all equipment is switched off at the mains wall
socket.
9
PRE/POWER CONNECTIONS
PWR AMP IN - To use your integrated amplifier just as a
power amplifier, connect the output of your pre-amplifier to
the PWR AMP IN sockets.The integrated amplifier’s internal
selector switch must be changed to disconnect the pre-amp
stages of the unit. Contact your dealer or Arcam for more
details. Under these circumstances it has exactly the same
specification and performance as an Arcam power amplifier.
PRE-AMP OUT - To use your integrated amplifier as a
preamplifier, connect the PRE-AMP OUT sockets to the
input sockets of your power amplifier.With a power
amplifier of the correct gain (e.g. An Arcam P25)
this allows you to bi-amplify ('bi-amp') suitable loudspeakers,
giving significant improvements in sound quality (see section
on BI-WIRING/ BI-AMPING).
+ R
+ L
4-16 OHMS
SP2
SP1
+ R -+ L -
1236 7
bkblbmbnbobpbq
bt
8 9 brbs
ck
54
cl
cm
230V
POWER INLET
L
R
PHONO OPTION
MM
MC
PROC/TAPE1
PLAY
IN
RECORD
OUT
R
LL
R
L
R
PRE OUT
GAIN
NORMAL
LOW
PWR IN
VCR/TAPE2
PLAY
IN
RECORD
OUT
DVD AV TUNER CD
AUX
CONTROL
OUT
REMOTE
IN
CONNECTING TO OTHER EQUIPMENT
Integrated amp - Setting up
Continued
Bi-wiring improves the sound of your system because it divides the
high and low frequency signal currents into separate speaker
cables.This avoids signal distortions arising from the high and low
frequency currents interacting with one another within a single
cable, as in conventionally wired systems.
YOU WILL NEED
Speakers which have four terminals (connection points for
wires) on the back of each one. That’s eight in total.
If you have four terminals on each speaker they will be marked HF
(High frequency) and LF (Low Frequency).
Loudspeaker cables
Two pairs of loudspeaker cables per loudspeaker (which may be
joined at the amplifier end if your amplifier only has one pair of
output terminals per channel).
Or, a suitably terminated cable set (group of bound cables,
probably prepared by your dealer) capable of being used for
bi-wiring in one length.
WARNING
Do not make any connections to your amplifier while it is switched
on or connected to the mains supply. Please check all connections
thoroughly, make sure bare wires or cables are not touching the
amplifier in the wrong places (shorts) and you have connected
positive (+) to positive (+) and negative (-) to negative (-) before
attempting to re-connect the mains power supply.
Always ensure that the volume control on your amplifier is set to a
minimum before switching on.
1.
Remove the wire clips or bars which connect the pairs of terminals
together (terminal links) on each of the red and black terminals
on the rear of your loudspeakers.
THIS IS ESSENTIAL OR DAMAGE TO YOUR AMPLIFIERS
MAY RESULT WHICH IS NOT COVERED UNDER
WARRANTY.
2.
Connect the cables as shown in one of the pictures opposite,
dependant on the cables and the number of free amplifier
terminals you have, ensuring correct polarity at all times.
The positive (+) terminals on the right loudspeaker must go to the
positive (+) terminals on the right of the amplifier and the negative
(-) terminals on the right loudspeaker must go to the negative (-)
terminals on the right of the amplifier etc.
SHOWN BELOW IS THE BI-WIRING CONFIGURATION
USING ONE SET OF SPEAKER CONNECTIONS ON
THE INTEGRATED AMPLIFIER.
If you are using one pair of bi-wireable speakers and another pair
that is not, you should connect your bi-wireable speakers as shown
above, to just one set of the amplifier terminals. This leaves the
second set of terminals to connect the non bi-wireable speakers to.
SHOWN BELOW IS THE BI-WIRING CONFIGURATION
USING BOTH SETS OF SPEAKER CONNECTIONS ON
THE INTEGRATED AMPLIFIER.
Bi-wiring your speakers
HOW TO BI-WIRE LOUDSPEAKERS
LEFT SPEAKER
RIGHT SPEAKER
+ HF –
+ LF –
+ HF –
+ LF –
R
L
+
+
+ HF –
+ LF –
+ LF –
R
L
+
+
+ HF –
INTEGRATED AMPLIFIER
INTEGRATED AMPLIFIER
LEFT SPEAKER
RIGHT SPEAKER
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam FMJ P25 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam FMJ P25 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info