578788
13
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
13
Bi-wiring and bi-amping loudspeakers
BEFORE YOU START
WARNING: Do not make any connections to your
amplifier while it is switched on or connected to the mains
supply.
Before switching on please check all connections thoroughly,
making sure bare wires or cables are not touching the
amplifier in the wrong places (which could cause short
circuits) and you have connected positive (+) to positive
and negative () to negative.
Always ensure that the volume control on your amplifier is
set to minimum before starting these procedures.
BI-WIRING YOUR LOUDSPEAKERS
Bi-wiring improves the sound of your system because it divides the
high and low frequency signal currents into separate speaker cables.
This avoids signal distortions arising from the high and low frequency
currents interacting with one another within a single cable, as in
conventionally wired systems.
You will need:
Speakers with four input terminals each: these will be marked HF
(High Frequency) and LF (Low Frequency).
Loudspeaker cables two pairs of cables per loudspeaker (which may
be joined at the amplifier end if your amplifier has only one pair of
output terminals per channel). Or, a suitably terminated cable set (a
loom, probably prepared by your dealer and capable of being used for
bi-wiring in one length).
How to bi-wire loudspeakers
1. Remove the terminal links on the rear of your loudspeakers
WARNING: This step is essential or damage to your
amplifier may result which is not covered under warranty.
2. Connect the cables as shown in the diagram below, ensuring
correct polarity at all times.
BI-AMPING YOUR SYSTEM
The performance of your system can be further enhanced over that
achieved with bi-wiring, by extending the principle one stage further
to include separate amplification for the low and high frequency drive
units in each loudspeaker enclosure.
Connect the integrated amplifier to the high frequency (HF) terminals
and connect the power amplifier to the low frequency (LF) terminals.
You will need:
Speakers with four input terminals each (as with bi-wiring): these will
be marked HF (High Frequency) and LF (Low Frequency).
Two amplifiers one of these would be the A32 and the other an
Arcam power amplifier (e.g. P35).
Loudspeaker cables two pairs of cables per loudspeaker or a suitably
terminated cable set (a loom, probably prepared by your dealer and
capable of being used for bi-amping in one length).
Interconnect cables one pair of high quality interconnect cables.
How to set up a bi-amped system
1. Remove the terminal links on the rear of your loudspeakers.
WARNING: This step is essential or damage to your amplifier
may result which is not covered under warranty.
2. Connect the cables as shown in the diagram below, ensuring
correct polarity at all times.
3. Use the interconnect cables to connect the
PRE OUT sockets of
the A32 to the corresponding AUDIO IN sockets of the power
amplifier.
Bi-wiring using one set of connections on amplifier
Recommended bi-amping configuration
Arcam A32 amplifier
RL
Right
speaker
HF
LF
+
+
+
HF
LF
+
+
+
Left
speaker
RL
Arcam P35 power amplifier
+ +
R
L
+ +
Right
speaker
HF
LF
+
+
HF
LF
+
+
Left
speaker
Arcam A32 amplifier
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam FMJ A32 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam FMJ A32 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info