578756
4
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
A70
E-4
Installation
Positioning the unit
Place your amplifier on a level, firm surface. Avoid placing the unit in direct sunlight or near sources of
heat or damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space such as a bookcase or cabinet as
both of these will impede air flow through the ventilation slots.
Connecting to loudspeakers
You can connect one or two pairs of loudspeakers to your amplifier,
provided each pair is rated between 8–16Ω. If one or both pairs have an
impedance of less than 8Ω, the combined load on the amplifier falls below
4Ω and could cause an overload. If so, the overload protection circuit may
engage and the amplifier will not work.
To connect one pair of loudspeakers, use the SP1 terminals.
Caution: Do not over tighten the loudspeaker terminals or use a
wrench, pliers, etc., as this could cause damage to the terminals
which will not be covered under warranty.
SP1 and SP2 terminals
4
Both sets of loudspeaker terminals can be muted by pressing the MUTE button on the remote control. To
switch SP1 and SP2 independently, use the front panel switches (see page 6,
2
) or the remote control
(see page 9).
Your amplifier is fitted with industry standard loudspeaker terminals. The terminal accepts spade
terminals or bare wires.
To connect a spade terminal or bare wire, unscrew the red (or black) part of the loudspeaker terminal
first. Insert the wire or spade terminal and screw it back up.
Connect the right speaker to the terminals on the back of your amplifier marked R and the left speaker
to the terminals marked L.
Connect your loudspeakers so that the red (positive/+) terminal on each loudspeaker is connected to
the red (positive/+) terminal on the amplifier. Your loudspeaker cables may be marked to show polarity
(negative/ and positive/+), if not, then the positive terminal can usually be identified by a ridge or
coloured marking.
Now connect your loudspeakers’ black (negative/) terminals to the black (negative/) terminals on the
amplifier. Ensure that no stray strands of inner wires are allowed to touch another cable or the amplifier’s
casing. This can cause a short circuit and damage your amplifier!
Connecting to a power supply
Mains lead
The appliance is normally supplied with a moulded mains plug already fitted to the lead. If for any
reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a
potential shock hazard when inserted into the mains socket. Should you require a new mains lead,
contact your Arcam dealer.
Wrong plug?
Check that the plug supplied with the unit fits your supply and that your mains supply voltage agrees
with the voltage setting (115V or 230V) indicated on the rear panel of the unit
2
before plugging in.
If your mains supply voltage or mains plug is different, consult your Arcam dealer or Arcam Customer
Support on +44 (0)1223 203200.
The product must be earthed.
Plugging in
Push the plug (IEC line socket) of the power cable supplied with the unit into the socket (POWER INLET)
1
in the back of the unit. Make sure it is pushed in firmly.
Put the plug on the other end of the cable into your power supply socket and switch the socket on.
Wiring your loudspeakers





4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam DiVA A70 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam DiVA A70 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info