537057
3
Verklein
Vergroot
Pagina terug
1/87
Pagina verder
3
E
N
HOW TO OPERATE YOUR ANGELCARE
®
MONITOR
Charger adapter
socket
STEP 1
Power ON/OFF
Parents unit
pager
Sound volume
UP/DOWN
Connect the long sensor pad cord into the nursery unit.
Insert 4 AAA regular batteries (not included) into nursery unit (for battery
backup in case of power failure).
Connect AC adapter to nursery unit and plug adapter into an electrical
outlet in the baby’s room.
After both units are properly installed you may adjust the sensor pad
sensitivity level (if necessary).
Note: After each start up, the monitor needs up to 1 minute before the
movement function is ready to be used.
Once the parents unit is fully charged (after 15 hours) turn the unit ON and
turn the nursery unit ON. If the parents unit is turned ON and the
nurser
y unit is OFF, the parents unit will start beeping after 1 minutes.
After 4 seconds, the unit will shuts itself off.
The different available options are programmable but you can use
the units right away, with the following factory settings :
- Sound,
movement and tic activated
- Out of range notification OFF
- Voice activated ON
- Temperature display ON, Room temperature control OFF
- Parents unit alarm ON, vibration OFF
- Speaker volume at 3
- Voice sensitivity at 2
To avoid feedback (whistling sound), keep both units at least 3 meters
apart (10 feet).
You can adjust the sound volume with the arrow buttons.
To turn the night light ON, move the right wing button UP.
Insert 4 AAA NIMH rechargeable batteries (included) into parents unit.
NEVER use regular alkaline batteries.
Connect AC adapter to parents unit charger and plug adapter into an
electrical outlet. Let charge for 15 continuous hours before using the
monitor for the first time.
Charger adapter
socket
Sensor pad cord
socket
Adapter socket
Sensor pad
sensitivity dial
I sensor pad 2 sensor pads
POSITION OF SENSOR PAD UNDER MATTRESS
Crib center Crib center
Position the sensor pad as shown above. Make sure the printed side faces up. Do not place any bedding between the mattress and the sensor pad.
Secure the sensor pad cord to crib using a tie wrap. Run the cord on the floor to ensure it is out of the baby’s reach.
The sensor pad must rest on a completely flat and rigid surface. Place a 6mm (1/4”) plywood to cover the full size of the crib base. Make sure
the sensor pad’s cord passes underneath the mattress as shown above.
Keep at
least 38 cm
(15 inches)
apart
Sensor Pad(s) 1 or 2
INSTALLATION OF THE SENSOR PAD UNDER THE MATTRESS
STEP 2
INSTALLATION OF THE NURSERY UNIT
Battery
compartment
STEP 3
INSTALLATION OF THE PARENTS UNIT
Battery
compartment
STEP 4
HOW YO USE YOUR ANGELCARE© MONITOR
Power ON/OFF
Movement
capture indicator
(Flashing)
ON/ OFF Night
light button
Power ON indicator
Low battery
indicator
Microphone
Speaker
AC401 international.qxd 6/10/08 11:44 AM Page 3
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Angelcare AC401de luxe bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Angelcare AC401de luxe in de taal/talen: Nederlands, Duits, Frans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Angelcare AC401de luxe

Angelcare AC401de luxe Gebruiksaanwijzing - Nederlands - 7 pagina's

Angelcare AC401de luxe Gebruiksaanwijzing - English - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info